IKEA LÖNSET 092.410.81 Bed Base instructions manual

The IKEA LÖNSET 092.410.81 is a sturdy, slatted bed base designed to provide optimal support and ventilation for your mattress. It is compatible with various IKEA bed frames and is constructed from birch wood and steel. Below are key sections for safety, assembly, use, care, and troubleshooting.

Parts & Tools

Before assembly, verify all parts are included. Key components: Slatted bed base, center support beam, screws, wing nuts, and plastic glides.

Tools required: Phillips screwdriver (not included).

Safety Information

Read all instructions before assembly and use.

1. Weight Limit: Maximum load 220 lbs (100 kg) per slatted panel.
2. Assembly: Assemble on a soft surface to avoid scratching parts.
3. Stability: Ensure all screws and wing nuts are tightened securely.
4. Children: Keep small parts away from children during assembly.

WARNING! Do not stand or jump on the bed base. Use only with compatible IKEA bed frames. Failure to follow instructions may result in injury or damage.

Assembly Instructions

Assemble the bed base before placing it into the bed frame.

1. Step 1: Lay both slatted panels side by side on a clean, flat surface (e.g., carpet).
2. Step 2: Insert the center support beam between the two panels, aligning the holes.
3. Step 3: Attach plastic glides to each end of the center beam (if not pre-attached).
4. Step 4: Secure the panels to the center beam using the M8 screws and wing nuts. Hand-tighten firmly.
5. Step 5: Ensure all connections are secure and the base lies flat.

Tip: It is easier to assemble with two people.

Installation in Bed Frame

Once assembled, place the bed base into your IKEA bed frame.

1. Step 1: Ensure the bed frame is on a level surface and is empty.
2. Step 2: Lift the assembled bed base and carefully lower it into the frame.
3. Step 3: Align the plastic glides on the center beam with the support rails in the frame.
4. Step 4: The bed base should rest securely on the side rails of the frame. There should be no wobbling.
5. Step 5: Place your mattress on top of the bed base.

CAUTION! Do not force the bed base into the frame. Ensure it is properly aligned to prevent damage.

Specifications

• Product Name: LÖNSET Bed Base
• Article Number: 092.410.81
• Material: Birch wood, Steel, Plastic
• Color: Birch natural
• Dimensions (Assembled): Varies by size (Twin, Full, Queen, King). Please refer to packaging.
• Weight Capacity: 440 lbs (200 kg) total (220 lbs per panel).
• Compatibility: Designed for use with IKEA bed frames (e.g., MALM, HEMNES, Brimnes series). Check compatibility before purchase.

Adjusting & Leveling

The bed base provides firm support. For optimal comfort and mattress longevity:

1. Ventilation: The slatted design allows air to circulate under the mattress.
2. Support: The flexible slats adjust to body weight for even support.
3. Leveling: If the bed base rocks, ensure the bed frame is on a level floor. Adjust frame legs if possible.
4. Noise: If squeaking occurs, check that all wing nuts are tight and that the base is properly seated in the frame.

Care & Maintenance

Proper care will extend the life of your bed base.

1. Cleaning: Wipe with a dry or slightly damp cloth. Do not use harsh chemicals or abrasive cleaners.
2. Inspection: Periodically check that all screws and wing nuts are tight (every 6 months).
3. Storage: If disassembled, store in a dry place. Avoid excessive humidity.

CAUTION! Do not expose to direct sunlight or moisture for prolonged periods. Do not use a steam cleaner.

Warranty Information

This IKEA product is covered by a limited warranty. Refer to the IKEA warranty leaflet included in the packaging or visit www.ikea.com for full terms and conditions.

Contact: For warranty claims or service, contact your local IKEA store or visit the IKEA website.

Troubleshooting

Note: For missing parts or further assistance, contact IKEA customer service with your article number (092.410.81).

Service: Visit www.ikea.com or your local IKEA store.