IKEA KULLEN 104.847.85 5 Drawer Chest instructions manual

The IKEA KULLEN 104.847.85 is a 5-drawer chest made of particleboard, fiberboard, and ABS plastic, featuring a modern design with smooth-running drawers, integrated drawer stops to prevent accidental pull-out, and a sturdy metal frame. It requires assembly and includes all necessary hardware. Below are key sections for safety, parts list, assembly instructions, care, and warranty information.

1. Parts & Hardware Included 2. Safety Instructions 3. Assembly Instructions 4. Product Specifications 5. Drawer Installation & Adjustment 6. Care & Maintenance 7. Wall Attachment 8. Troubleshooting 9. Warranty & Support

Parts & Hardware Included

Before assembly, verify all parts are present. Key components: Chest frame panels, Drawer fronts and sides, Drawer bottoms, Metal drawer runners, Back panel, Cam locks, Screws, Dowels, Wall attachment device.

Part Description	Quantity	Image Reference
Side panel (left & right)	2	A1, A2
Top panel	1	B
Bottom panel	1	C
Back panel (fiberboard)	1	D
Drawer front (various sizes)	5	E1-E5
Drawer side (long & short)	10	F1, F2
Drawer bottom (particleboard)	5	G
Metal drawer runner	10	H
Cam lock with screw	12	I
Wooden dowel	20	J
Wall attachment bracket & screw	1 set	K

Safety Instructions

Read all instructions before assembly. Use on stable, level surface.

Prevent tipping: Always secure chest to wall using provided wall attachment device.
Weight capacity: Do not exceed 55 lbs (25 kg) per drawer. Distribute weight evenly.
Assembly: Use only provided hardware. Do not overtighten screws.
Children safety: Do not let children climb or play on drawers. Keep small hardware away from children.

WARNING! Serious or fatal crushing injuries can occur from furniture tip-over. Always secure furniture to wall.

Assembly Instructions

Estimated assembly time: 45-60 minutes. Tools needed: Phillips screwdriver (included: Allen key).

Prepare workspace: Lay all parts on a soft surface to avoid scratches.
Assemble frame: Connect side panels (A1, A2) to top (B) and bottom (C) using dowels (J) and cam locks (I). Tighten cam locks clockwise.
Attach back panel: Place frame face down. Align back panel (D) and secure with provided screws.
Install drawer runners: Attach metal runners (H) to inside of frame at marked positions using screws.
Assemble drawers: Connect drawer sides (F) to front (E) and back using dowels and cam locks. Insert drawer bottom (G) into grooves. Secure with screws underneath.
Install drawers: Slide drawer onto runners, ensuring it clicks into place. Test smooth operation.

Tip: Do not fully tighten cam locks until all parts are aligned.

Product Specifications

Product Name: KULLEN
Article Number: 104.847.85
Dimensions (W x H x D): 31 1/2 x 47 1/4 x 18 1/8 inches (80 x 120 x 46 cm)
Drawer interior dimensions: Varies by drawer (approx. 28 3/4 x 15 3/4 inches width/depth)
Weight: 66 lbs (30 kg)
Max load per drawer: 55 lbs (25 kg)
Material: Particleboard, Fiberboard, ABS plastic, Steel
Color: White
Finish: Foil

Drawer Installation & Adjustment

Drawers feature integrated stops and smooth-glide runners.

Installation: Align drawer with runners, push in until it clicks. To remove, pull drawer fully out, press release tabs on both sides of runner, and lift drawer out.
Alignment: If drawer sticks or is uneven, loosen runner screws slightly, adjust drawer position, and retighten.
Drawer stop: Integrated stop prevents drawer from being pulled out completely accidentally.

Note: Lubrication is not required for runners. Clean with dry cloth if needed.

Care & Maintenance

Clean with damp cloth and mild detergent. Wipe dry immediately.

Surface: Use soft cloth. Avoid abrasive cleaners, solvents, or ammonia.
Drawers: Remove contents before cleaning. Do not overload.
Hardware: Check tightness of screws and cam locks periodically.

CAUTION! Do not use wax or polish on foil surfaces. Avoid excessive moisture.

Wall Attachment

CRITICAL: To prevent tip-over, attach chest to wall using provided bracket.

Locate wall stud using stud finder.
Position bracket against wall at desired height (recommended: top third of chest back).
Secure bracket to wall stud with provided screw (use appropriate anchor if no stud).
Place chest against wall, aligning back of chest with bracket.
Secure chest to bracket using screw through pre-drilled hole in back panel.

WARNING! If chest is not anchored, it can tip over and cause serious injury.

Troubleshooting

Issue	Possible Cause	Solution
Drawer sticks or doesn't close smoothly	Misaligned runners, overloaded drawer	Realign runners; reduce weight; ensure drawer is assembled correctly.
Frame wobbles	Cam locks not tightened, uneven floor	Tighten all cam locks; place on level surface; attach back panel securely.
Drawer front uneven	Drawer not fully seated on runners	Remove drawer, reinstall ensuring it clicks into place; adjust runner position.
Missing hardware	Packaging error	Contact IKEA customer service for replacement parts.
Scratches on surface	Assembly on hard surface	Assemble on soft blanket; use touch-up paint (available from IKEA).

Warranty & Support

IKEA limited warranty applies. See IKEA warranty for details.

Warranty period: Varies by country. Typically 1-10 years for structural integrity.
Support: For missing parts or assembly help, contact IKEA customer service.
Website: www.ikea.com for assembly videos and guides.
Phone: 1-888-888-4532 (US)

Recycling: Dispose of packaging responsibly. Product is recyclable where facilities exist.