IKEA KRAGSTA 202.866.38 Table instructions manual

The IKEA KRAGSTA 202.866.38 is a round dining table with a diameter of 90 cm, featuring a solid particleboard top with oak veneer and a black stained ash veneer edge band. It includes a sturdy underframe with a black powder-coated steel base. Below are key sections for safety, assembly, care, and warranty information.

1. Product Overview 2. Package Contents 3. Tools Required 4. Assembly Instructions 5. Safety Precautions 6. Care & Maintenance 7. Specifications 8. Warranty Information 9. Troubleshooting

Product Overview

The KRAGSTA table combines a warm oak-look surface with a modern black metal base, suitable for dining or as a work surface. The design is stable and easy to clean.

Component	Description
Table Top	Round, 90 cm diameter, particleboard with oak veneer and black stained ash veneer edge
Underframe	Black powder-coated steel base with four legs
Assembly Hardware	Included in package (see Package Contents)
Weight Capacity	Max. load 50 kg evenly distributed
Height	74 cm from floor to table top

Package Contents

Before assembly, verify all parts are present and undamaged.

Table top (1 piece)
Metal underframe with pre-attached legs (1 assembly)
Assembly screws (4 pieces)
Allen key (1 piece)
Instruction manual (this document)

IMPORTANT! If any part is missing or damaged, contact IKEA customer service. Do not attempt assembly with incomplete or damaged parts.

Tools Required

Only the included Allen key is needed for assembly. No additional tools are required.

Assembly Instructions

Follow these steps carefully. We recommend two people for assembly.

Prepare Workspace: Clear a soft, flat area large enough to lay the table top upside down (protected with a blanket or cardboard).
Position Underframe: Place the metal underframe upside down on the floor.
Attach Top to Base: Carefully turn the table top upside down onto the protected surface. Align the underframe centrally on the underside of the table top. The pre-drilled holes in the underframe should match the holes in the table top.
Secure with Screws: Using the included Allen key, insert and tighten the four screws through the underframe into the table top. Do not overtighten.
Final Check: Carefully turn the assembled table upright. Ensure all legs are firmly on the floor and the table does not wobble.

WARNING! The table top is heavy. Lift with your legs, not your back. Use two people to avoid injury or damage.

Safety Precautions

Assemble on a soft surface to prevent scratches.
Do not exceed the maximum load of 50 kg.
Do not sit or stand on the table.
Keep away from direct heat sources (radiators, stoves) and prolonged direct sunlight to prevent warping or fading.
Ensure the table is on a level surface to prevent tipping.

Care & Maintenance

To maintain appearance and longevity:

Cleaning: Wipe the table top with a damp cloth and a mild household cleaner. Dry immediately with a soft, clean cloth.
Stains: For stubborn stains, use a mild soap solution. Never use abrasive cleaners, scouring pads, or solvents.
Base: Clean the metal base with a dry or slightly damp cloth.
Protection: Use coasters under glasses and placemats under hot dishes to protect the veneer surface.

CAUTION! Never soak the table with water or cleaning liquids. Do not use wax or polish.

Specifications

Article Number: 202.866.38
Design: Round dining table
Diameter: 90 cm
Height: 74 cm
Top Thickness: 2.8 cm
Top Material: Particleboard, Oak veneer, Black stained ash veneer edge
Underframe Material: Steel, Epoxy/polyester powder coating
Weight: Approximately 18 kg
Max Load: 50 kg

Warranty Information

This IKEA product is covered by a limited warranty. Refer to the IKEA warranty terms included in the original packaging or available at www.IKEA.com. The warranty covers material and manufacturing defects under normal household use for the specified period from the date of purchase. Proof of purchase is required.

Troubleshooting

Issue	Possible Cause	Corrective Action
Table wobbles	Uneven floor or loose screws	Check floor level. Tighten all assembly screws with the Allen key. If floor is uneven, use furniture pads under the appropriate leg(s).
Scratches on surface during assembly	Assembly on hard surface	Always assemble on a soft, protective surface like a blanket.
Screw won't tighten	Cross-threaded or misaligned	Unscrew completely, ensure hole alignment is perfect, and re-insert screw straight.
Surface stain	Liquid spill or heat mark	Clean immediately with a damp cloth. For heat marks, try gently rubbing with a mild non-gel toothpaste on a soft cloth, then wipe clean. Test in an inconspicuous area first.
Veneer lifting	Exposure to moisture or heat	Keep table away from moisture and heat sources. For minor lifting, use a small amount of wood glue and clamp until dry. For major issues, contact IKEA.

Customer Service: For missing parts, damaged components, or further assistance, contact IKEA customer service at 1-888-888-4532 or visit www.IKEA.com.