IKEA KONSTRUERA 093.922.06 Drawer instructions manual

The IKEA KONSTRUERA 093.922.06 is a modular drawer unit designed for assembly and integration into various IKEA storage systems. It features a sturdy construction, smooth-gliding drawer slides, and a clean, modern design. Below are key sections for safety, parts identification, step-by-step assembly, installation, adjustment, care, and troubleshooting.

1. Parts & Hardware Included 2. Tools Required 3. Safety Instructions 4. Step-by-Step Assembly 5. Installation into Frame 6. Drawer Slide Adjustment 7. Weight Capacity & Limitations 8. Care & Maintenance 9. Disassembly & Moving 10. Warranty Information 11. Troubleshooting

Parts & Hardware Included

Key components: Drawer front panel, drawer sides, drawer back panel, drawer bottom panel, drawer runners (slides), screws, cam locks, dowels.

Part NumberDescriptionQuantity
ADrawer Front Panel1
BDrawer Side Panel (Left)1
CDrawer Side Panel (Right)1
DDrawer Back Panel1
EDrawer Bottom Panel1
FDrawer Runner (Slide) - Left1
GDrawer Runner (Slide) - Right1
HCam Lock Screws4
IRunner Mounting Screws8
JWooden Dowels4

Tools Required

You will need the following tools for assembly. IKEA tools are included where specified.

  1. Hex Key (Allen Wrench) - Included.
  2. Screwdriver (Phillips #2) - Not included.
  3. Hammer (for tapping dowels) - Not included.
  4. Soft Mallet (recommended) - Not included.
  5. Clean, flat workspace.

WARNING! Using incorrect tools may damage parts or result in improper assembly.

Safety Instructions

Read all instructions before beginning assembly.

  1. Assemble on a soft, clean surface to prevent scratches.
  2. Keep small parts and packaging away from children and pets.
  3. Ensure all connections are tight and secure before use.
  4. Do not exceed the maximum weight capacity.
  5. Use two people for lifting and installing the drawer into a frame.

CAUTION! Furniture tip-over hazard. Secure the final cabinet/unit to the wall according to IKEA's instructions.

Step-by-Step Assembly

Installation into Frame

This drawer is designed for IKEA frames with compatible runner mounting points.

  1. Ensure the cabinet frame is level and stable.
  2. Fully extend the cabinet runner halves already installed in the frame.
  3. Align the drawer runners with the cabinet runners. Hook the front of the drawer runner into the front of the cabinet runner.
  4. Push the drawer firmly and evenly into the frame until it clicks into place at the back.
  5. Test the drawer by opening and closing it several times. The motion should be smooth.

Tip: Install the drawer without the front panel first to ensure alignment, then attach the front panel for final adjustment.

Drawer Slide Adjustment

Most IKEA runners have a self-closing mechanism and adjustment features.

For side-to-side alignment: Open the drawer fully. Look for an adjustment lever or screw on the side of the cabinet runner. Turn to move the drawer left or right.

For height/leveling: The drawer front can often be adjusted after installation. Loosen the screws securing the front panel to the drawer box slightly, adjust the panel up/down or left/right, then re-tighten.

Sticking or Not Closing: Check for obstructions inside the drawer or frame. Ensure the runners are clean and properly engaged.

Weight Capacity & Limitations

Maximum distributed weight: 55 lbs (25 kg).

  1. Distribute weight evenly. Do not place all heavy items at the front.
  2. Avoid placing extremely sharp or pointed objects directly on the drawer bottom without protection.
  3. This drawer is for dry, indoor use only.

WARNING! Exceeding the weight limit can damage runners, cause drawer failure, and create a safety hazard.

Care & Maintenance

Unload drawer before cleaning. Use a damp cloth with mild soap; dry immediately.

CAUTION! Do not use abrasive cleaners, scouring pads, or harsh chemicals. Do not soak any parts in water.

Disassembly & Moving

To remove the drawer: Open it fully, locate the plastic release tabs on both sides of the cabinet runners, press them upward (or downward as indicated), and lift the drawer out.

For full disassembly, reverse the assembly steps. Keep all hardware in a labeled bag.

Warranty Information

IKEA limited warranty. Refer to the IKEA warranty booklet included with your purchase or available at IKEA stores. Warranty covers material and manufacturing defects under normal household use. Proof of purchase is required. For support, visit www.ikea.com or contact your local IKEA store.

Troubleshooting

SymptomPossible CauseCorrective Action
Drawer is wobblyCam locks not tight; dowels not fully seatedCheck all cam connections; ensure dowels are fully inserted into corresponding holes.
Drawer sticks or doesn't roll smoothlyMisaligned runners; obstructionRemove drawer and check for alignment. Ensure nothing is blocking the slides inside the cabinet.
Drawer front is unevenFront panel not adjusted properlyLoosen the screws attaching the front to the drawer box, align the panel, and re-tighten.
Bottom panel pops outNot correctly seated in groovesRemove drawer, lift bottom panel, and re-insert firmly into all four grooves until it lies flat.
Cannot install drawer into frameCabinet runners not fully extended; misalignmentFully pull out the cabinet runners. Align drawer runners carefully and push straight back.

Missing Parts? Contact IKEA customer service with your article number (093.922.06).

Service: www.ikea.com or your local IKEA store.

IKEA KONSTRUERA 093.922.06 Drawer instructions manual © - All Rights Reserved 2025