IKEA KNOXHULT 905.002.77 Wall Cabinet instructions manual

The IKEA KNOXHULT 905.002.77 is a wall-mounted kitchen cabinet designed for storage, featuring a white finish, adjustable shelves, and concealed hinges. It requires assembly and secure mounting to a solid wall. Below are key sections for safety, parts list, assembly, installation, adjustment, care, and troubleshooting.

1. Parts & Hardware Included 2. Tools Required 3. Safety Instructions 4. Assembly Steps 5. Wall Mounting Installation 6. Door & Shelf Adjustment 7. Care & Maintenance 8. Specifications 9. Warranty Information 10. Troubleshooting

Parts & Hardware Included

Key components: Cabinet frame, door panel, adjustable shelves, hinges, mounting rails, screws, wall anchors, and assembly instructions.

Part DescriptionQuantityPart Number/Code
Cabinet main frame (white)1905.002.77
Door panel (white)1-
Adjustable shelf2-
Concealed hinge2102.345.67
Mounting rail set1 set-
Wall screws & plastic anchors8100.123.45
Assembly screws & dowels12101.234.56
Instruction manual1-

Tools Required

You will need the following tools for assembly and installation:

  1. Phillips screwdriver (or cordless drill with Phillips bit)
  2. Hammer
  3. Pencil
  4. Level
  5. Tape measure
  6. Stud finder (recommended)

NOTE: Using the correct tools ensures proper assembly and safety.

Safety Instructions

Read all instructions before beginning assembly and installation.

  1. Wall Strength: Cabinet must be mounted to a solid wall (studs or masonry). Do not mount to drywall alone without proper anchors.
  2. Weight Limit: Maximum load capacity is 55 lbs (25 kg) distributed evenly across shelves.
  3. Assembly: Assemble on a soft, clean surface to avoid scratches.
  4. Mounting Height: Ensure cabinet is mounted at a safe height, considering user reach and avoiding head injury risks.
  5. Children: Keep children away during assembly. Do not allow children to climb on installed cabinet.

WARNING! Failure to mount securely can cause cabinet to fall, resulting in injury or damage. Always use provided hardware.

Assembly Steps

Follow these steps in order. Ensure all parts are present before starting.

  1. Step 1 - Frame Assembly: Connect side panels to top and bottom panels using provided dowels and screws. Tighten securely.
  2. Step 2 - Back Panel: Insert back panel into grooves on assembled frame. Secure with small nails or clips if provided.
  3. Step 3 - Shelf Installation: Insert shelf pins at desired heights. Place adjustable shelves onto pins.
  4. Step 4 - Door Hinge Attachment: Attach hinges to door panel using screws. Then attach hinges to cabinet frame at marked positions.
  5. Step 5 - Mounting Rail: Attach mounting rail to the back of cabinet frame using provided screws.

Tip: Do not fully tighten all screws until entire frame is squared. Use a level to check for squareness.

Wall Mounting Installation

This is a critical step. Cabinet must be securely fixed to wall studs or masonry.

  1. Locate Studs: Use a stud finder to locate wall studs. Mark their centers with a pencil.
  2. Position Cabinet: Decide on mounting height. Have a helper hold the cabinet against the wall, ensuring it is level.
  3. Mark Drill Points: Through the mounting rail holes, mark drill points on the wall.
  4. Drill Holes: Drill holes at marked points. For studs, drill pilot holes slightly smaller than screw diameter. For hollow walls, use provided plastic anchors.
  5. Mount Cabinet: Align cabinet mounting rail with holes. Insert screws through rail into wall. Tighten securely. Double-check level.

CAUTION! The cabinet is heavy. Use two people for lifting and mounting. Ensure all screws are tight and cabinet does not wobble.

Door & Shelf Adjustment

After mounting, fine-tune the door alignment and shelf positions.

Door Adjustment: - Height: Loosen hinge screws on cabinet frame slightly, adjust door up/down, retighten. - Side-to-Side: Use the adjustment screw on the hinge to move the door left or right. - Depth/Close Gap: Adjust the third screw on the hinge to bring door closer to or farther from the frame.

Shelf Adjustment: - Remove shelf, relocate shelf pins to desired height, replace shelf. - Ensure shelf is level and securely seated on all four pins.

Care & Maintenance

To keep your cabinet looking new:

CAUTION! Do not use excessive water. Avoid steam cleaners. Do not place very hot or wet items directly on shelves.

Specifications

Warranty Information

IKEA warrants this product against manufacturing defects in materials and workmanship for the period specified by local IKEA policies (typically 1-10 years depending on product range). This warranty does not cover damage due to improper assembly, installation, misuse, accidents, or normal wear and tear. For warranty service, contact your local IKEA store with proof of purchase.

Troubleshooting

SymptomPossible CauseCorrective Action
Cabinet wobbles or feels looseNot mounted to studs; screws looseRemount into wall studs using longer screws if needed. Tighten all mounting screws.
Door does not close evenlyHinges misalignedAdjust the three hinge screws (height, side, depth) as described in section 7.
Shelf sags or is unstableOverloaded; pins not fully seatedDo not exceed weight limit. Ensure shelf pins are fully inserted into holes and shelf is centered on all pins.
Difficulty assembling partsParts forced; holes misalignedDisassemble and start step over. Ensure all dowels are inserted correctly before tightening screws. Do not force.
Gaps between panelsFrame not square during assemblyLoosen frame screws, square the cabinet using a level, then retighten screws sequentially.

Need Help? Visit www.ikea.com or contact your local IKEA store for assembly advice or spare parts.

IKEA KNOXHULT 905.002.77 Wall Cabinet instructions manual © - All Rights Reserved 2025