IKEA KNOXHULT 703.722.71 Corner Cabinet instructions manual

The IKEA KNOXHULT 703.722.71 is a modular corner cabinet designed for kitchen use, part of the KNOXHULT series. It features a white finish, adjustable shelves, soft-closing hinges, and is designed to fit seamlessly into kitchen corners to maximize storage space. This manual provides essential information for safety, assembly, installation, use, care, and troubleshooting.

1. Safety Information 2. Package Contents & Tools Needed 3. Assembly Instructions 4. Installation & Mounting 5. Adjustments & Features 6. Care & Maintenance 7. Specifications 8. Troubleshooting 9. Warranty & Support

Safety Information

Read all instructions before assembly and installation.

Work Area: Assemble on a clean, flat, protected surface to avoid scratches.
Lifting: The cabinet is heavy. Use two people for lifting and mounting to prevent injury.
Wall Mounting: Must be securely attached to wall studs using provided hardware. Do not rely on drywall alone.
Children: Keep children away during assembly. Ensure installed cabinet is stable and doors are closed when not in use.
Tools: Use correct tools. Wear safety glasses if drilling.

WARNING! Failure to properly secure cabinet to wall can result in tipping, causing serious injury or death.

Package Contents & Tools Needed

Before starting, verify all parts are present.

Part Description	Quantity	Image Ref.
Cabinet frame (white)	1	A
Doors (white) with hinges pre-attached	2	B
Adjustable shelves	2	C
Back panel	1	D
Mounting rail	1	E
Cam locks, screws, dowels, wall anchors	1 set	F
Instruction manual	1	-

Tools You Provide: Phillips screwdriver, hammer, level, measuring tape, pencil, stud finder, electric drill.

Assembly Instructions

Follow steps in order. Do not fully tighten screws until assembly is complete.

Prepare Frame: Lay cabinet frame front-side down on protected surface.
Attach Back Panel: Align back panel (D) with frame. Secure using provided screws.
Install Cam Locks: Insert dowels into side panels as shown. Connect side, top, and bottom panels using cam locks. Tighten with screwdriver.
Install Shelves: Insert shelf supports (pegs) into inner walls at desired heights. Place shelves (C) on supports.
Mount Rail: Attach mounting rail (E) to the upper back of the cabinet frame using provided screws.
Attach Doors: Hang doors (B) onto hinge plates on frame. Adjust door alignment using hinge screws (see Section 5).

Tip: Ensure all cam locks are turned to the locked position (usually a 90° turn).

Installation & Mounting

Cabinet must be mounted to wall studs.

Locate Studs: Use stud finder to locate at least two wall studs in the corner area. Mark their centers with pencil.
Position Cabinet: With help, lift cabinet into corner. Use level to ensure it is perfectly horizontal and vertical.
Secure to Wall: Drill pilot holes through mounting rail into wall studs. Secure cabinet with long screws provided. If studs don't align, use heavy-duty wall anchors for additional points.
Final Check: Gently try to pull cabinet away from wall. It should not move. Ensure doors open and close freely without hitting adjacent walls or cabinets.

CAUTION! The weight of the cabinet and its contents must be supported by the wall mounting. Verify stability.

Adjustments & Features

Door Adjustment: Doors can be adjusted in three planes:

Height: Loosen screws on hinge where it attaches to cabinet frame, adjust door up/down, retighten.
Depth: Turn the screw on the side of the hinge to move door closer to or further from the frame.
Side-to-Side: Loosen screws on hinge plate inside door, adjust alignment, retighten.

Soft-Close Hinges: Hinges have built-in soft-closing mechanism. Do not oil.

Shelf Adjustment: Shelves are adjustable. Move shelf supports to desired height for customization.

Care & Maintenance

Cleaning: Wipe exterior and interior with a damp cloth and mild detergent. Dry immediately.

Avoid: Abrasive cleaners, scouring pads, or harsh chemicals. Do not use excessive water.

Inspection: Periodically check that mounting screws are tight and hinges function properly.

CAUTION! Do not overload shelves. Maximum load per shelf: 15 kg (33 lbs).

Specifications

Article Number: 703.722.71
Color: White
Material: Particleboard, foil, ABS plastic
Dimensions (HxWxD): 80 cm x 60 cm x 60 cm (31 ½" x 23 ⅝" x 23 ⅝")
Door Swing: 90 degrees
Weight: 18.5 kg (40.8 lbs)
Max. Shelf Load: 15 kg (33 lbs) per shelf
Hinge Type: Soft-closing, adjustable

Troubleshooting

Problem	Possible Cause	Solution
Cabinet wobbles or feels loose	Not secured to wall studs; screws loose	Remount into studs using provided long screws. Tighten all frame and mounting screws.
Doors are misaligned	Hinges need adjustment	Follow adjustment steps in Section 6. Adjust height, depth, and side-to-side alignment.
Door does not close smoothly	Obstruction; hinge mechanism dirty	Check for items blocking door. Wipe hinge with dry cloth. Do not lubricate soft-close mechanism.
Shelf sags or is unstable	Overloaded; shelf supports not fully seated	Reduce weight below 15 kg. Ensure shelf supports (pegs) are fully inserted into holes.
Gaps between panels	Cam locks not fully tightened; frame not square	Check all cam locks are turned to locked position. Ensure frame is assembled on a flat surface.

Warranty & Support

This IKEA product is covered by a limited warranty. Refer to the IKEA warranty document included in the packaging or available at IKEA stores for full terms.

Spare Parts: For missing or replacement parts, contact IKEA customer service with the article number (703.722.71).

Support: For assembly help or other inquiries:

Visit: www.ikea.com
Contact your local IKEA store.
Refer to online assembly guides at IKEA website.

Recycling: Dispose of packaging materials responsibly. The cabinet can be disassembled for recycling at end of life.