IKEA KLÖVEN 504.276.46 Table instructions manual

The IKEA KLÖVEN 504.276.46 is a versatile and sturdy table designed for various indoor settings. This manual provides essential information for safe assembly, proper use, care, and maintenance of your table. Below are key sections covering safety, parts identification, step-by-step assembly, usage guidelines, care instructions, and warranty information.

1. Parts & Hardware 2. Safety Instructions 3. Assembly Instructions 4. Specifications 5. Usage & Placement 6. Care & Maintenance 7. Disassembly & Moving 8. Troubleshooting 9. Warranty Information

Parts & Hardware

Before assembly, verify all parts are included. Check packaging materials thoroughly.

Part NameQuantityDescription/Image Ref.
Tabletop1Main surface panel
Leg A (Long)2Long side legs with pre-drilled holes
Leg B (Short)2Short side legs with pre-drilled holes
Support Brackets4Metal brackets for leg attachment
Cam Lock Nuts8Plastic locking fasteners
Screws (Type A)16For bracket-to-tabletop connection
Screws (Type B)8For bracket-to-leg connection
Allen Key1Tool provided for assembly
Protective Felt Pads4For leg bottoms

Safety Instructions

Read all instructions before assembly. Keep for future reference.

  1. Work Area: Assemble on a clean, soft, non-scratch surface.
  2. Lifting: Tabletop is heavy; use two people for handling.
  3. Tools: Use only the provided Allen key. Do not over-tighten screws.
  4. Children & Pets: Keep away from assembly area. Small parts are choking hazards.
  5. Stability: Ensure all legs are firmly attached before use. Do not sit or stand on the table.

WARNING! Failure to follow instructions may result in injury or damage to the product.

Assembly Instructions

Estimated assembly time: 30-45 minutes. Follow steps in order.

  1. Prepare: Unpack all parts. Identify each piece using the Parts list.
  2. Attach Brackets to Tabletop: Position the 4 support brackets on the underside of the tabletop at the marked locations. Secure each bracket using 4 Type A screws per bracket (16 total). Hand-tighten, then use the Allen key for a final quarter-turn.
  3. Attach Legs: Insert Leg A (Long) into the two brackets on one long side. Align holes. Insert and hand-tighten 2 Type B screws per leg (4 total for this side). Repeat for the other long side with the second Leg A. Attach Leg B (Short) to the brackets on the two short sides using the same method.
  4. Secure Cam Locks: On the inside of each leg, locate the cam lock holes. Insert a cam lock nut into each hole (8 total). Turn clockwise with the Allen key until fully locked and flush. This secures the leg to the bracket.
  5. Final Check & Leveling: Turn the table upright on a flat floor. Check stability. If the table rocks, adjust the protective felt pads on the bottom of the legs by twisting.

Tip: Do not fully tighten any screw until all screws for that component are started.

Specifications

Usage & Placement

Designed for indoor residential use.

  1. Surface Protection: Use coasters under glasses and placemats under hot dishes to prevent heat marks and scratches.
  2. Weight Limit: Do not exceed the 50 kg maximum load. This includes items placed on the table.
  3. Placement: Place on a flat, stable floor. Avoid direct sunlight, heat sources (radiators), and areas of high humidity (e.g., bathrooms).
  4. Uneven Floors: Use the adjustable felt pads to stabilize the table if your floor is slightly uneven.

CAUTION! This table is not suitable for commercial use, outdoor use, or as a workbench.

Care & Maintenance

Proper care will extend the life of your table.

  1. Cleaning: Wipe the tabletop with a soft, slightly damp cloth. Dry immediately with a clean, dry cloth.
  2. Stain Removal: For stubborn stains, use a mild soap solution. Never use abrasive cleaners, scouring pads, or solvents (e.g., acetone, alcohol).
  3. Frame/Legs: Dust with a dry cloth. For marks, use a damp cloth and dry thoroughly.
  4. Felt Pads: Check periodically. Replace if worn to protect your floor.

WARNING! Never soak the tabletop or allow liquids to pool, as this can cause swelling and damage the material.

Disassembly & Moving

To move the table, partial disassembly is recommended.

  1. Turn the table upside down on a protected surface.
  2. Using the Allen key, unlock all 8 cam lock nuts by turning counter-clockwise.
  3. Remove the Type B screws securing the legs to the brackets.
  4. Gently detach the legs. The brackets can remain attached to the tabletop.
  5. Move the tabletop and legs separately. Use two people for the tabletop.
  6. Reassemble following the Assembly Instructions.

Tip: Keep all hardware in a labeled bag during moving to avoid loss.

Troubleshooting

IssuePossible CauseSolution
Table wobblesUneven floor; Legs not fully secured; Felt pads not adjusted.Check floor level. Tighten all cam locks and screws. Adjust felt pads by twisting.
Screw won't tightenCross-threaded; Wrong screw used.Back screw out completely and restart. Verify screw type from parts list.
Gap between leg and tabletopBracket not flush; Cam lock not engaged.Loosen bracket screws, reposition bracket flush, retighten. Ensure cam lock is turned to locked position.
Scratches on surfaceAbrasive cleaning; Dragging objects.Use felt pads under decorative items. Clean with soft cloth only. Minor scratches can be concealed with a matching furniture touch-up pen.
Missing partPackaging error.Contact IKEA customer service with your article number (504.276.46) for replacement parts.

Warranty Information

This IKEA product is covered by a limited warranty. Refer to the IKEA warranty leaflet included in the packaging or available at www.IKEA.com for full terms and conditions, including warranty duration and coverage.

Customer Support: For assembly help, missing parts, or other inquiries, please contact IKEA customer service:

IKEA KLÖVEN 504.276.46 Table instructions manual © - All Rights Reserved 2025