IKEA KINNAHULT 504.884.23 Table Lamp Instructions Manual

The IKEA KINNAHULT 504.884.23 is a modern table lamp featuring a fabric shade and metal base, designed for use with an E27 bulb (max 15W LED or 40W incandescent, not included). It includes an in-line switch on the power cord, requires assembly, and is intended for indoor use. Below are key sections for safety, assembly, installation, operation, care, and troubleshooting.

1. Safety Information 2. Package Contents 3. Assembly Instructions 4. Installation & Setup 5. Operation 6. Specifications 7. Care & Maintenance 8. Troubleshooting 9. Warranty & Support

Safety Information

Important safety warnings and precautions for using the KINNAHULT table lamp.

Warning	Description
Electrical Safety	Use only with correct voltage (120V AC). Do not use if cord or plug is damaged.
Bulb Specification	Use only E27 base bulb, max 15W LED or 40W incandescent. Higher wattage may cause overheating.
Placement	Keep away from water, heat sources, and flammable materials. For indoor use only.
Children & Pets	Place out of reach of young children. Do not let pets chew on cord.
Assembly	Ensure lamp is unplugged during assembly. Follow steps carefully.

Package Contents

Unpack and verify all parts are included before assembly.

Fabric lamp shade (pre-assembled)
Metal lamp base
E27 socket with attached power cord and in-line switch
Assembly hardware (screws, if required)
Instruction manual (this document)

NOTE: Light bulb is not included. Contact IKEA if any parts are missing.

Assembly Instructions

Follow these steps to assemble your KINNAHULT table lamp.

Place the metal base on a stable, flat surface.
Attach the E27 socket to the base according to the provided diagram (usually screws into pre-threaded hole).
Carefully place the fabric shade over the socket, ensuring it sits securely on the base or socket ring.
Route the power cord neatly from the base. Do not pinch or twist the cord.
Ensure all connections are tight and the lamp is stable.

CAUTION! Do not plug in or turn on the lamp during assembly.

Installation & Setup

Setting up your lamp for first use.

Choose a location: Stable, flat surface near a power outlet.
Insert bulb: Screw an E27 bulb (max 15W LED/40W incandescent) into the socket firmly but do not overtighten.
Plug the power cord into a standard 120V AC wall outlet.
Test the lamp: Use the in-line switch on the cord to turn the lamp ON/OFF.

Tip: For best light distribution, ensure the shade is straight and not tilted.

Operation

Using your KINNAHULT table lamp.

Power On/Off: Use the in-line switch on the power cord.
Bulb Replacement: Always unplug lamp first. Allow bulb to cool if recently on. Unscrew old bulb, screw in new E27 bulb within wattage limits.
Adjustment: The shade is not adjustable; position the entire lamp for desired lighting angle.

WARNING! Never touch bulb when lamp is on or immediately after turning off, as it may be hot.

Specifications

Model: KINNAHULT 504.884.23
Type: Table Lamp
Material: Fabric shade, Metal base
Bulb: 1 x E27 socket (max 15W LED or 40W incandescent)
Power Cord: With in-line switch, length approximately 1.8m (6 ft)
Input Voltage: 120V AC, 60Hz
Dimensions (approx.): Height: 35 cm (13.8 in), Base diameter: 15 cm (5.9 in)
Weight: 1.2 kg (2.6 lbs)
Intended Use: Indoor residential use

Care & Maintenance

To keep your lamp in good condition.

Unplug lamp before any cleaning.
Shade: Use a soft, dry cloth or a vacuum with a brush attachment for dust. Do not wash.
Base & Socket: Wipe with a dry or slightly damp cloth. Do not use abrasive cleaners.
Cord: Check periodically for damage. Do not pull cord to unplug.

CAUTION! Never immerse lamp in water or use liquid cleaners on the shade or electrical parts.

Troubleshooting

Symptom	Possible Cause	Corrective Action
Lamp does not turn on	Not plugged in; switch off; bulb burnt out	Plug into outlet; turn switch ON; replace bulb with correct type.
Flickering light	Loose bulb; faulty bulb	Ensure bulb is screwed in tightly. Try a different bulb.
Lamp gets hot	Bulb wattage too high	Use only recommended bulb (max 15W LED/40W incandescent).
Unstable	Base not assembled correctly; uneven surface	Re-tighten base assembly. Place on a flat, stable surface.
Switch not working	Faulty switch or cord	Unplug and contact IKEA support. Do not attempt repair.

Warranty & Support

This IKEA product is covered by a limited warranty. For details, refer to the IKEA warranty booklet included with your purchase or visit www.ikea.com.

Contact IKEA: For product support, spare parts, or assembly questions, visit the IKEA website or contact your local IKEA store.

Recycling: Dispose of the lamp and bulb according to local electronic waste regulations. Do not dispose of with household trash.