IKEA KATTARP 104.668.66 Ceiling Lamp instructions manual

The IKEA KATTARP 104.668.66 is a modern ceiling lamp designed for general room lighting. It features a minimalist design, energy-efficient LED light source, dimmable functionality (with compatible dimmers), and a white finish. Below are key sections for safety, features, installation, setup, operation, and troubleshooting.

1. Safety Instructions 2. Package Contents 3. Tools Required 4. Installation Steps 5. Electrical Connection 6. Mounting to Ceiling 7. Bulb Replacement 8. Dimming Instructions 9. Care & Cleaning 10. Specifications 11. Troubleshooting

Safety Instructions

Read all instructions before installation and keep for future reference.

WarningDescription
Electrical SafetyAlways turn off power at the circuit breaker before installation. Ensure wiring is de-energized.
Professional InstallationIf unsure, hire a qualified electrician. Installation must comply with local electrical codes.
Weight LimitDo not exceed the maximum weight rating for the mounting surface.
Heat DissipationEnsure adequate ventilation; do not cover lamp or place near heat sources.
Children & PetsKeep packaging materials away from children to avoid suffocation risk.

Package Contents

Unpack and verify all parts are present before starting installation.

  1. Ceiling lamp shade (white).
  2. Mounting bracket with screws.
  3. Integrated LED light module.
  4. Wire connectors (2 pieces).
  5. Instruction manual (this document).

WARNING! Do not discard packaging until all parts are confirmed. Contact IKEA if any item is missing.

Tools Required

Gather these tools before beginning installation.

CAUTION! Use proper safety equipment (gloves, eye protection) when drilling or handling wires.

Installation Steps

Follow these steps in order for safe and correct installation.

  1. Turn off power: Switch off at circuit breaker and verify with voltage tester.
  2. Remove old fixture (if present): Disconnect wires and remove mounting hardware.
  3. Install mounting bracket: Secure to ceiling junction box using provided screws.
  4. Connect wires: Match lamp wires to house wires (black to black, white to white, green/yellow to ground). Use wire connectors.
  5. Attach lamp: Align lamp with bracket and secure according to instructions.
  6. Install light module: Ensure it is properly seated and secure.
  7. Restore power: Turn on circuit breaker and test lamp operation.

Electrical Connection

Proper wiring is critical for safety and function.

Wire Color (Lamp)Connection ToNote
Black (or Brown)House Live (Black)Line / Hot wire
White (or Blue)House Neutral (White)Neutral wire
Green/YellowHouse Ground (Green/Bare)Safety ground - MUST be connected

Tip: Twist wires together securely before applying wire connectors. Ensure no bare wire is exposed.

Mounting to Ceiling

Secure mounting ensures stability and safety.

  1. Position bracket: Align over junction box so screw holes match.
  2. Secure bracket: Use provided screws to fasten bracket firmly to box.
  3. Hang lamp: Lift lamp and hook onto bracket (or align screw holes).
  4. Final secure: Tighten locking screws or turn locking ring clockwise until snug.
  5. Check stability: Gently pull down on lamp to confirm it is securely attached.

WARNING! Do not support lamp weight solely by electrical wires. The bracket must carry the full weight.

Bulb Replacement

This model uses an integrated, non-user-replaceable LED module.

CAUTION! Do not attempt to open or repair the LED module. There are no user-serviceable parts inside.

Dimming Instructions

The lamp is dimmable when used with compatible dimmer switches.

  1. Compatibility: Use only trailing-edge (ELV) dimmers designed for LED loads. Check dimmer packaging or manufacturer's website.
  2. Installation: Replace standard wall switch with compatible dimmer (performed by qualified electrician).
  3. Operation: Turn dimmer knob or slide control to adjust brightness.
  4. Flickering/Buzzing: If occurs, the dimmer may be incompatible. Try a different dimmer model.

Note: Not compatible with standard incandescent (leading-edge) dimmers.

Care & Cleaning

Regular cleaning maintains appearance and light output.

  1. Turn off and let cool: Disconnect power and wait for lamp to cool completely.
  2. Dust: Use a soft, dry microfiber cloth or feather duster.
  3. Clean: For marks, dampen cloth with mild soapy water. Wring out thoroughly.
  4. Dry: Wipe immediately with a dry cloth.

CAUTION! Do not use abrasive cleaners, solvents, or spray directly on the lamp. Do not immerse in water.

Specifications

Troubleshooting

SymptomPossible CauseCorrective Action
Lamp does not turn onPower off / Tripped breakerCheck circuit breaker; ensure wall switch is on; verify power to outlet.
Lamp flickersIncompatible dimmer / Loose connectionUse a compatible LED dimmer; check and tighten all wire connections.
Dimming not smoothDimmer compatibility / Load too lowEnsure dimmer is designed for low-wattage LED loads; consult dimmer manual.
Buzzing soundIncompatible dimmer / TransformerReplace with a compatible trailing-edge (ELV) dimmer.
Light output decreasedLED end of life / Dust accumulationClean lamp shade; if problem persists, LED module may need replacement (contact IKEA).

Warranty: Refer to IKEA warranty terms included with purchase.

Support: For assistance, visit www.ikea.com or contact your local IKEA store.

IKEA KATTARP 104.668.66 Ceiling Lamp instructions manual © - All Rights Reserved 2025