IKEA KALLAX 202.946.19 Shelf instructions manual

The IKEA KALLAX 202.946.19 is a versatile, modular shelving unit designed for easy assembly and flexible storage. Constructed from particleboard with a foil finish, it features a classic square design that can be used horizontally or vertically, and can be combined with other KALLAX series inserts and accessories. Below are key sections for safety, parts list, assembly instructions, care, and warranty information.

1. Parts & Hardware Included 2. Tools Required 3. Safety Instructions 4. Step-by-Step Assembly 5. Mounting to Wall (Important!) 6. Care & Maintenance 7. Specifications 8. Troubleshooting 9. Warranty & Support

Parts & Hardware Included

Before starting, check that you have all parts listed below.

Part Name	Quantity	Description / Part Number
Long side panel	2	Main vertical panels
Short side panel / Shelf	5	Horizontal dividers and top/bottom panels
Wood dowel	16	For connecting panels
Cam lock	16	For securing connections
Screw	16	For cam locks
Wall attachment device	1 set	Bracket and screws for securing to wall
Instruction manual	1	This document

Tools Required

You will need the following tools (not included):

Phillips screwdriver
Hammer (for gently tapping dowels if needed)
Pencil and level (for wall mounting)
Drill with appropriate drill bit (for wall mounting into studs or masonry)

Safety Instructions

WARNING! Serious or fatal crushing injuries can occur from furniture tipping over. This furniture must be permanently fixed to the wall.

Tip-over Hazard: Unanchored furniture can tip over. Always secure this furniture to the wall using the provided wall attachment device.
Assembly: Assemble on a soft, clean surface to avoid scratching parts. Keep small parts away from children during assembly.
Weight Limit: Do not exceed the maximum load of 13 kg (29 lbs) per shelf compartment. The total maximum load for the unit is 65 kg (143 lbs).
Placement: Place on a level, stable floor. Do not place near direct heat sources or in damp areas.

Step-by-Step Assembly

Follow these steps in order. Do not fully tighten cam locks until the structure is square.

Step 1: Identify all panels (long sides, short sides/shelves).
Step 2: Insert wood dowels into the pre-drilled holes on the long side panels as shown in the diagram.
Step 3: Connect the first short side panel (shelf) to one long side panel by aligning the dowels and holes. Hand-tighten the cam locks into the screws on the opposite side.
Step 4: Repeat Step 3 for the remaining shelves, building the unit on its back.
Step 5: Attach the final long side panel to complete the box structure.
Step 6: Ensure all joints are aligned, then fully tighten all cam locks using a screwdriver.
Step 7: Carefully stand the unit upright.

Tip: Do not overtighten cam locks, as this can strip the particleboard.

Mounting to Wall (Important!)

This is a mandatory safety step to prevent tip-over.

Decide on the final placement of the shelf unit.
Locate wall studs using a stud finder. For solid walls, use appropriate wall plugs.
Place the unit against the wall. Using the provided bracket as a template, mark the screw holes on the wall through the top inside of the unit.
Drill pilot holes at the marked spots.
Attach the bracket to the wall using the provided screws, ensuring it is secure.
Place the unit back against the wall and secure it to the bracket using the screw provided in the wall attachment set.
Check that the unit is stable and cannot be pulled away from the wall.

WARNING! If you cannot secure the furniture to the wall, do not use it. The wall attachment device is designed for standard wood stud walls. For other wall types (e.g., concrete, brick), use suitable fixings available separately.

Care & Maintenance

Clean with a damp cloth wrung out in a mild soap solution. Wipe dry immediately.

DO NOT: Use abrasive cleaners, scouring pads, or solvents. Avoid excessive moisture.

Specifications

Article Number: 202.946.19
Design: KALLAX
Color: White
Material: Particleboard, Fiberboard, Acrylic paint, Foil
Dimensions (W x H x D): 77 x 147 x 39 cm (30 1/4 x 57 7/8 x 15 3/8 inches)
Package Weight: Approximately 25 kg (55 lbs)
Max Load/Shelf: 13 kg (29 lbs)
Max Load/Unit: 65 kg (143 lbs)

Troubleshooting

Issue	Possible Cause	Solution
Unit is wobbly	Cam locks not tightened; floor uneven; not attached to wall	Check and tighten all cam locks. Ensure unit is on level floor. MUST be attached to wall.
Dowels won't fit	Misaligned holes; debris in holes	Ensure panels are correctly oriented. Clear any packaging debris from holes. Do not force.
Shelf sags under weight	Exceeding weight limit	Remove excess weight. Distribute weight evenly. Do not exceed 13 kg per compartment.
Cannot attach to wall	Wrong wall type; missing hardware	Use appropriate fixings for your wall type (e.g., concrete anchors). Contact IKEA for replacement hardware.
Scratches on surface	Assembled on hard surface	Assemble on a blanket or carpet. Minor scratches can be touched up with a matching wax crayon.

Warranty & Support

This IKEA product is covered by a limited warranty. For details, refer to the IKEA warranty booklet included in the packaging or visit www.IKEA.com.

Need Help? Visit the IKEA website for assembly guides and customer service: www.IKEA.com or contact your local IKEA store.

Recycling: At the end of its life, disassemble and recycle the materials according to local regulations.