IKEA KALLAX 004.779.31 Shelf instructions manual

The IKEA KALLAX 004.779.31 is a versatile shelving unit designed for storage and display. It features a modular cube design, is constructed from particleboard with foil finish, and includes assembly hardware. Below are key sections for safety, parts list, assembly instructions, care, and warranty information.

1. Parts & Hardware 2. Safety Instructions 3. Assembly Steps 4. Mounting to Wall 5. Weight Limits & Usage 6. Care & Cleaning 7. Troubleshooting 8. Warranty & Support

Parts & Hardware

Before assembly, check that you have all parts listed below.

Part Description	Quantity	Image Reference
Main shelf panel (large)	4	A
Inner divider/shelf panel	4	B
Back panel	1	C
Cam lock dowels	16	D
Screws	20	E
Wall attachment device	1 set	F
Allen key	1	G
Instruction manual	1	-

Note: All hardware is included in one bag. Do not discard any parts until assembly is complete.

Safety Instructions

Read all instructions before assembly. Keep children and pets away during assembly.

Choking hazard: Small parts included. Keep away from children under 3 years.
Tip-over hazard: Furniture can tip over. Always secure to wall using provided wall attachment device.
Weight limit: Do not exceed maximum load per shelf as specified.
Proper surface: Assemble on a soft, clean surface to avoid scratching.
Correct tools: Use only the provided Allen key. Do not overtighten screws.

WARNING! Serious or fatal crushing injuries can occur from furniture tip-over. Always secure to wall.

Assembly Steps

Follow steps in order. Allow approximately 30-45 minutes for assembly.

Step 1: Lay all large panels (A) on a soft surface with the finished side down.
Step 2: Insert cam lock dowels (D) into pre-drilled holes on the sides of panels as shown in diagram.
Step 3: Connect panels together by aligning dowels and gently tapping until flush.
Step 4: Insert inner divider panels (B) to create cube compartments. Secure with screws (E).
Step 5: Attach the back panel (C) using provided screws. Ensure it is square and flush.
Step 6: Tighten all cam locks using the Allen key (G) by turning clockwise until snug.
Step 7: Carefully turn the unit upright. Check stability before loading.

Tip: Do not fully tighten cam locks until all panels are connected and aligned.

Mounting to Wall

This step is mandatory to prevent tip-over.

Locate wall studs using a stud finder. The unit must be anchored into solid wood or masonry.
Position the unit against the wall in its desired permanent location.
Use the provided wall attachment device (F). Attach the bracket to the top back of the unit using screws.
Mark drill holes on the wall through the bracket. Drill pilot holes into the studs.
Secure the bracket to the wall with suitable screws (not always included; check your hardware).
Ensure the unit does not rock or move. Re-tighten if necessary.

CAUTION! If you cannot secure it to a wall, do not use this furniture. Use appropriate wall fasteners for your wall type.

Weight Limits & Usage

Max load per shelf: 13 kg (29 lbs).
Total max load: 25 kg (55 lbs) for the entire unit.
Recommended use: Books, decorative items, media storage, folded clothing.
Not recommended: Heavy electronics (large CRT TVs, large amplifiers), aquariums, or excessive weight concentrated in one cube.
Placement: Keep away from direct sunlight, heat sources, and high humidity to prevent warping.

Distribute weight evenly. Place heavier items on lower shelves.

Care & Cleaning

To maintain appearance and longevity.

Dust regularly with a soft, dry cloth.
For stains, use a mild soap solution. Dampen (do not soak) a cloth, wipe gently, and dry immediately.
Do not use abrasive cleaners, scouring pads, or solvents.
Avoid placing wet items directly on the surface.

CAUTION! Never use wax, polish, or furniture spray on the foil surface.

Troubleshooting

Issue	Possible Cause	Solution
Unit wobbles	Uneven floor; cam locks not tight; wall not secured	Place on level surface; tighten all cam locks and screws; ensure wall bracket is securely fastened.
Cam lock won't tighten	Dowel not fully inserted; cross-threaded	Disassemble step, ensure dowel is straight and fully seated in hole, then re-tighten.
Shelf sags	Weight limit exceeded	Remove excess weight. Distribute load evenly. Do not exceed 13 kg per shelf.
Scratches during assembly	Assembled on hard surface	Assemble on carpet or blanket. Minor scratches can be touched up with a matching marker (not included).
Missing part	Packaging error	Contact IKEA customer service with article number (004.779.31) for replacement parts.

Warranty & Support

IKEA limited warranty applies. For your safety, retain this manual.

Warranty: Refer to the IKEA warranty document included in packaging or at IKEA stores.
Spare Parts: Available at IKEA stores or via customer service.
Assembly Help: Visit the IKEA website for assembly videos.
Contact: IKEA Customer Support: 1-888-888-4532 (IKEA) or visit www.ikea.com.

Recycling: Dispose of packaging and product responsibly according to local regulations.