IKEA IVAR 604.839.72 Cabinet instructions manual

The IKEA IVAR 604.839.72 is a versatile pine cabinet designed for the IVAR storage system. It features adjustable shelves, a hinged door, and a simple, timeless design that can be stained, painted, or left natural. Below are key sections for safety, parts list, assembly instructions, installation, care, and troubleshooting.

1. Parts & Hardware Included 2. Tools Required 3. Assembly Instructions 4. Installation & Mounting 5. Adjustments & Configuration 6. Care & Maintenance 7. Safety Information 8. Specifications 9. Warranty & Support 10. Troubleshooting

Parts & Hardware Included

Before assembly, verify all parts are present. Key components: Cabinet frame, door, adjustable shelves, hinges, screws, wall attachment device.

Part DescriptionQuantityImage Ref.
Cabinet side panel2A
Cabinet top/bottom panel2B
Cabinet back panel1C
Door panel1D
Adjustable shelf2E
Hinge with screws2F
Wall attachment device1 setG
Shelf support peg8H
Cam lock with screw4I

Tools Required

Tools not included. You will need:

  1. Phillips screwdriver
  2. Hammer (for wall attachment if needed)
  3. Level (for installation)
  4. Pencil (for marking)
  5. Measuring tape

WARNING! Use correct tools to avoid damaging parts or injury.

Assembly Instructions

Follow steps in order. Work on a clean, flat surface.

  1. Prepare parts: Lay out all parts as shown in diagram.
  2. Assemble frame: Connect side panels (A) to top/bottom panels (B) using cam locks (I). Insert and tighten screws.
  3. Attach back panel: Position back panel (C) and secure with provided screws.
  4. Install shelf supports: Insert shelf support pegs (H) into pre-drilled holes at desired heights.
  5. Mount hinges: Attach hinges (F) to door (D) using screws, then attach hinges to cabinet frame.
  6. Install shelves: Place adjustable shelves (E) on support pegs.
  7. Check alignment: Ensure door opens/closes smoothly; adjust hinges if necessary.

CAUTION! Do not overtighten screws; this may split wood.

Installation & Mounting

To prevent tipping, cabinet must be secured to wall.

  1. Locate wall studs using stud finder.
  2. Position cabinet against wall at desired height and location.
  3. Use level to ensure cabinet is straight; mark screw holes.
  4. Attach using wall attachment device (G) provided; ensure screws penetrate studs.
  5. Test stability by gently pulling on cabinet.

WARNING! Serious injury can occur from unsecured furniture tipping over. Always secure to wall.

Adjustments & Configuration

Shelf height: Move shelf support pegs to different pre-drilled holes to change shelf positions.

Door alignment: Loosen hinge screws slightly to adjust door up/down or in/out; retighten.

Finish customization: Cabinet is untreated pine; can be stained, painted, or sealed as desired.

Care & Maintenance

Use dry or slightly damp cloth for cleaning. For stubborn stains, use mild soap solution; wipe dry immediately.

CAUTION! Do not use abrasive cleaners, scouring pads, or harsh chemicals. Avoid excessive moisture.

Safety Information

Specifications

Warranty & Support

IKEA limited warranty applies. For missing parts or assembly support, contact IKEA customer service with article number (604.839.72) and proof of purchase.

Contact: Visit www.ikea.com or your local IKEA store.

Troubleshooting

SymptomPossible CauseCorrective Action
Cabinet wobblesUneven floor; loose jointsCheck floor level; tighten all cam locks and screws.
Door does not close properlyMisaligned hingesLoosen hinge screws, reposition door, retighten.
Shelf sagsOverloadedReduce weight; do not exceed 55 lbs total.
Difficulty assembling jointsParts misalignedDisassemble step, ensure parts are oriented correctly per diagram.
Missing hardwarePackaging errorContact IKEA for replacement parts with article number.

Note: For persistent issues, refer to online assembly video at IKEA website.

IKEA IVAR 604.839.72 Cabinet instructions manual © - All Rights Reserved 2025