IKEA IVAR 194.173.91 Cabinet instructions manual

The IKEA IVAR 194.173.91 is a versatile pine wood cabinet designed for the IVAR storage system. It features a classic, natural wood finish, adjustable shelves, and a simple, functional design suitable for various rooms. Below are key sections for safety, parts list, assembly instructions, mounting, care, and warranty information.

1. Parts & Hardware Included 2. Tools Required 3. Safety Information 4. Assembly Instructions 5. Mounting to Wall 6. Adjusting Shelves 7. Care & Maintenance 8. Specifications 9. Troubleshooting 10. Warranty & Support

Parts & Hardware Included

Before assembly, check that you have all parts listed below.

Part Description	Quantity	Image Ref.
Cabinet side panel (pine)	2	A
Cabinet top panel	1	B
Cabinet bottom panel	1	C
Cabinet back panel (fiberboard)	1	D
Adjustable shelf (pine)	2	E
Door panel with hinge pre-drills	1	F
Cam lock dowels	8	G
Cam locks	8	H
Shelf support pins	16	I
Wall mounting bracket & screws	1 set	J
Door hinge set	1 set	K
Door handle	1	L

Tools Required

You will need the following tools (not included):

Phillips screwdriver
Hammer (for tapping dowels)
Level
Pencil
Measuring tape
Electric drill (optional, for wall mounting)

Safety Information

WARNING! To prevent serious injury and damage:

Tip-over Hazard: This cabinet can tip over if not properly secured to the wall. Always use the included wall attachment device.
Lifting: Cabinet is heavy. Use two people to lift and assemble.
Children: Do not let children climb on or play with the cabinet.
Surface: Assemble on a soft, clean surface to avoid scratching the wood.
Hardware: Keep small hardware away from children to avoid choking.

Assembly Instructions

Follow these steps in order. Do not fully tighten cam locks until all parts are joined.

Prepare Panels: Lay side panels (A) flat. Insert cam lock dowels (G) into pre-drilled holes on the inner faces of both side panels.
Attach Top & Bottom: Align top panel (B) and bottom panel (C) between the side panels. Connect using the cam locks (H). Turn cam locks 90° clockwise to lock (use a screwdriver if tight).
Install Back Panel: Place the cabinet frame upright. Slide the fiberboard back panel (D) into the grooves on the rear of the side, top, and bottom panels. Secure with provided nails or screws if included.
Insert Shelf Supports: Decide shelf heights. Insert shelf support pins (I) into the desired holes on the inside of both side panels.
Place Shelves: Rest the adjustable shelves (E) on the support pins.
Attach Door: Following hinge instructions (K), attach the hinge plates to the door (F), then attach the hinges to the inside of the cabinet's side panel. Adjust door alignment as needed.
Attach Handle: Screw the door handle (L) to the door at your preferred height.

Tip: Ensure all cam locks are fully turned to the locked position before moving the cabinet.

Mounting to Wall

THIS STEP IS MANDATORY TO PREVENT TIP-OVER.

Decide on final location for the cabinet, ensuring it is against a solid wall (stud preferred).
Place the cabinet in position. Using a pencil, mark the wall through the holes in the provided wall mounting bracket (J).
Move the cabinet aside. Drill pilot holes at your marks using an appropriate drill bit for your wall type (e.g., wood stud or wall anchor).
Secure the bracket to the wall using the provided screws.
Lift the cabinet back into place and hook it onto the mounted bracket. Ensure it is securely engaged.
Use a level to check that the cabinet is straight.

Adjusting Shelves

The shelves are adjustable to accommodate items of different heights.

Empty the shelf you wish to move.
Lift the shelf up and slightly forward to disengage it from the support pins.
Remove the shelf completely.
Reposition the shelf support pins (I) into the desired set of holes on the side panels.
Place the shelf back onto the new set of pins, ensuring it is level and seated securely.

Note: Do not exceed the maximum load of 15 kg (33 lbs) per shelf.

Care & Maintenance

To maintain the natural pine wood finish:

Dust regularly with a soft, dry or slightly damp cloth.
For stains, use a mild soap solution. Wipe dry immediately.
Avoid abrasive cleaners, scouring pads, or strong chemicals.
Protect from prolonged direct sunlight and excessive humidity to prevent warping or fading.
Tighten screws and hardware periodically as wood may settle over time.

CAUTION! Never soak the wood or use steam cleaners.

Specifications

Product Name: IVAR Cabinet
Article Number: 194.173.91
Material: Pine, Fiberboard (back panel)
Finish: Clear lacquer
Dimensions (W x H x D): 60 cm x 148 cm x 30 cm (23 5/8" x 58 1/4" x 11 3/4")
Door Swing: Right-hinged (can be mounted left-hinged)
Max. Shelf Load: 15 kg (33 lbs)
Weight: Approx. 18 kg (39.7 lbs)

Troubleshooting

Issue	Possible Cause	Solution
Cabinet is wobbly	Cam locks not fully tightened; uneven floor	Check and tighten all cam locks. Place on a level surface or use shims under the base.
Door does not close properly	Hinges misaligned; cabinet not square	Loosen hinge screws slightly, adjust door position, retighten. Ensure cabinet frame is assembled squarely.
Shelf sags or is unstable	Overloaded; support pins not fully inserted	Reduce weight on shelf. Ensure support pins are pushed completely into the holes.
Difficulty inserting dowels or pins	Holes misaligned or blocked	Do not force. Ensure you are using the correct part in the correct hole. Clear any debris from the hole.
Gaps between panels	Panels not aligned during assembly	Loosen cam locks, realign panels so edges are flush, then retighten locks.

Warranty & Support

This IKEA product is covered by a limited warranty. Refer to the IKEA warranty terms included in the packaging or available at IKEA stores.

Need help?

Visit the IKEA website: www.ikea.com
Use the IKEA Store App for assembly guides.
Contact your local IKEA customer support.
For missing parts, contact the IKEA store where the product was purchased with your receipt.