IKEA INSJÖN 203.419.08 Faucet instructions manual

The IKEA INSJÖN 203.419.08 is a single-handle kitchen faucet designed for easy installation and reliable operation. It features a pull-out spray head, ceramic disc cartridge for smooth control, and a durable finish. Below are key sections for safety, features, installation, operation, maintenance, and troubleshooting.

1. Features at a Glance 2. Installation 3. First-Time Setup 4. Specifications 5. Controls and Operation 6. Connecting to Water Supply 7. Using the Pull-Out Spray Head 8. Maintenance & Care 9. Regulatory Information 10. Troubleshooting

Features at a Glance

Key components: Single-handle mixer, pull-out spray head with hose, ceramic disc cartridge, aerator, mounting hardware.

Feature	Description
Single-handle control	Left/right for temperature, up/down for flow
Pull-out spray head	Extends for flexible rinsing; multiple spray patterns
Ceramic disc cartridge	Durable, drip-free operation
Aerator	Reduces splashing and conserves water
Mounting hardware	Includes base plate, nuts, washers, supply lines
Finish	Stainless steel look, corrosion-resistant
Hose length	Approximately 1.5 meters (59 inches)
Spray patterns	Stream and spray modes
Water connections	Standard 3/8" compression fittings
Warranty	Limited warranty as per IKEA policy

Installation

Unpack and inspect all parts. Ensure you have necessary tools: adjustable wrench, basin wrench, plumber's tape, bucket.

Shut off water supply: Turn off hot and cold water valves under sink.
Remove old faucet (if applicable): Disconnect supply lines and mounting nut.
Prepare sink: Clean mounting area; insert supply lines through mounting hole.
Mount faucet: Place base plate; secure from below with mounting hardware.
Connect supply lines: Attach hot (red) and cold (blue) lines to corresponding valves; use plumber's tape on threads.
Connect spray hose: Attach to faucet body and pull-out mechanism.
Check for leaks: Turn water supply on slowly; inspect all connections.

WARNING! Ensure water is off before installation. Do not overtighten connections. Follow local plumbing codes.

First-Time Setup

After installation, perform initial checks and adjustments.

Flush faucet: Run hot and cold water for 2 minutes to clear debris.
Check spray head function: Pull out hose; test stream and spray modes.
Adjust handle tension: If handle is loose/tight, adjust set screw under handle.
Set temperature limiter: Adjust safety stop to prevent scalding (if applicable).

CAUTION! Test water temperature before use to avoid burns. Ensure spray head retracts smoothly.

Specifications

Model: INSJÖN 203.419.08
Type: Single-handle kitchen faucet with pull-out spray
Finish: Stainless steel look
Cartridge: Ceramic disc
Hose Length: 1.5 m (59 in)
Spray Patterns: Stream and spray
Flow Rate: Meets local water efficiency standards
Mounting Holes: Fits standard 1-3/8" (35 mm) sink hole
Supply Connections: 3/8" compression fittings
Warranty: Refer to IKEA warranty terms

Controls and Operation

Handle controls both temperature and flow. Spray head offers multiple functions.

Handle Operation: Move left for hotter water, right for colder. Lift up to increase flow, push down to decrease/off.

Spray Head: Pull out for extended reach. Button on spray head toggles between stream (for filling) and spray (for rinsing). Release to retract automatically.

Aerator: Screws onto spout tip; reduces splashing. Clean periodically if flow decreases.

Connecting to Water Supply

Standard hot/cold connections under sink.

Ensure shut-off valves are easily accessible.
Use provided supply lines or compatible 3/8" lines.
Wrap threads with plumber's tape for secure seal.
Hand-tighten first, then use wrench for quarter turn—avoid overtightening.
Check for leaks after turning water on.

Tip: Label hot and cold lines for easy identification during installation.

Using the Pull-Out Spray Head

Designed for flexible cleaning and rinsing.

Pull spray head from faucet spout; hose extends up to 1.5 meters.
Press button on spray head to switch modes: stream (solid flow) or spray (wider pattern).
Release spray head after use; it should retract smoothly into place.
If hose does not retract, check for kinks or obstructions.
Do not pull hose at sharp angles; avoid stretching beyond length.

WARNING! Do not let spray head hang over sink edge; it may damage hose. Keep hose away from hot surfaces.

Maintenance & Care

Regular cleaning ensures longevity and performance.

Clean with mild soap and water; dry with soft cloth.
Avoid abrasive cleaners, scouring pads, or harsh chemicals.
Clean aerator every 3-6 months: unscrew, rinse, remove debris, reinstall.
Check for leaks periodically at connections and handle base.
If handle becomes stiff, contact IKEA support—do not force.

CAUTION! Do not use vinegar or descaling agents unless specified; they may damage finish.

Regulatory Information

Troubleshooting

Symptom	Possible Cause	Corrective Action
Low water flow	Clogged aerator	Clean or replace aerator.
Spray head not retracting	Kinked hose or weight issue	Straighten hose; ensure weight is properly installed.
Leaking from handle	Worn cartridge or loose handle	Tighten set screw; replace cartridge if needed.
Water temperature inconsistent	Supply line issues or cartridge	Check hot/cold supply; replace cartridge.
Spray pattern not changing	Debris in spray head	Clean spray head openings; check button function.
Faucet wobbles	Loose mounting	Tighten mounting nut under sink.

Note: For cartridge replacement or major repairs, refer to IKEA guide or contact support.

Service: Visit www.ikea.com or contact local IKEA customer service.