IKEA INLÄGG 094.816.55 Connection Hardware instructions manual

The IKEA INLÄGG 094.816.55 is a connection hardware set designed for assembling and securing IKEA furniture components. It includes specialized connectors, screws, and tools for creating stable joints in various furniture pieces. Below are key sections for safety, components, installation, assembly steps, usage guidelines, and troubleshooting.

Components Overview

Key components included in the INLÄGG 094.816.55 hardware set.

Safety Information

Important safety precautions before and during assembly.

1. Work on a clean, flat surface to prevent parts from rolling or falling.
2. Keep small parts away from children to avoid choking hazards.
3. Wear safety glasses when drilling or hammering components.
4. Ensure furniture is stable before applying weight or pressure.

WARNING! Do not overtighten connectors; this may strip threads or damage panels. Use tools provided.

Tools Required

Tools needed for assembly (some included in set).

1. Allen Key (included): For tightening cam lock screws.
2. Hammer: For inserting dowel pins (use gently).
3. Screwdriver: Phillips head for additional screws if needed.
4. Measuring Tape: For accurate alignment.
5. Pencil: For marking drill holes.

CAUTION! Use correct tool sizes to avoid damaging hardware or furniture.

Assembly Instructions

• Step 1: Identify all parts using the included diagram.
• Step 2: Insert dowel pins into pre-drilled holes in first panel.
• Step 3: Align second panel and connect via dowels.
• Step 4: Insert cam lock into designated hole on second panel.
• Step 5: Tighten connector screw into cam lock using Allen key.
• Step 6: Rotate cam lock disk to lock connection securely.
• Step 7: Verify joint is tight and panels are flush.

Installation Steps

Detailed installation for typical furniture assembly.

1. Lay panels on protected surface to prevent scratches.
2. Insert dowels into holes, tapping gently with hammer if needed.
3. Join panels, ensuring dowels align with corresponding holes.
4. Insert cam lock into exposed hole on joining panel.
5. Tighten screw until snug, then rotate cam lock 90° to lock.
6. Check stability; adjust if panels are misaligned.

Tip: Do not fully tighten until all connectors are in place and aligned.

Connection Types

Types of joints achievable with this hardware.

Right-Angle Joints: Most common for corners of cabinets, shelves.

T-Joints: For connecting shelves to vertical panels.

Flat Connectors: For joining panels edge-to-edge.

Cam locks provide hidden connections; dowels add shear strength and alignment.

Tightening Specifications

Proper torque and tightness guidelines.

1. Cam lock screws: Tighten until flush with panel surface, then ¼ turn further.
2. Dowel pins: Insert until fully seated; should not protrude.
3. Cam lock disk: Rotate until it clicks or stops; should not force.
4. Check alignment: Panels should be flush with no gaps.

WARNING! Over-tightening can crack particleboard or strip threads.

Usage Guidelines

Best practices for hardware use.

For Load-bearing Joints: Use multiple connectors per joint for stability. Avoid Excessive Weight: Do not exceed recommended load for furniture design. Temperature/Humidity: Keep in stable environment to prevent wood expansion/contraction affecting joints.

Care & Maintenance

Inspect joints periodically for looseness. Tighten if needed with Allen key. Clean with dry cloth; avoid moisture on metal parts to prevent rust.

CAUTION! Do not use lubricants on connectors; this may cause slipping.

Technical Specifications

Furniture Panel Thickness: Compatible with 16mm, 18mm, 25mm panels. Connector Material: Steel with zinc plating. Dowel Material: Beech wood. Screw Type: M6 thread. Torque: Hand-tighten only; no power tools. Weight Capacity: Varies by configuration; refer to furniture manual.

Troubleshooting

Support: For missing parts or further assistance, contact IKEA customer service or visit www.ikea.com.