IKEA IDÅSEN 504.963.81 Cabinet instructions manual

The IKEA IDÅSEN 504.963.81 is a versatile cabinet designed for home or office storage, featuring a clean Scandinavian design, durable construction, and adjustable shelves. It requires assembly and includes all necessary hardware. Below are key sections for safety, parts list, assembly steps, installation, care, and troubleshooting.

1. Parts & Hardware Included 2. Safety Information 3. Assembly Instructions 4. Installation & Mounting 5. Adjusting Shelves 6. Care & Maintenance 7. Specifications 8. Warranty Information 9. Troubleshooting

Parts & Hardware Included

Before assembly, verify all parts are present. Key components: Cabinet panels, doors, shelves, hinges, screws, cam locks, dowels, and mounting brackets.

Part Description	Quantity	Identification Code
Cabinet side panel (left)	1	A
Cabinet side panel (right)	1	B
Top panel	1	C
Bottom panel	1	D
Back panel	1	E
Adjustable shelf	2	F
Door panel	2	G
Hinge set	4	H
Cam lock with screw	8	I
Wooden dowel	12	J
Mounting bracket	2	K
Door handle	2	L

Safety Information

Read all instructions before assembly. Ensure a clean, spacious work area.

Use correct tools: Phillips screwdriver, hammer, level, measuring tape.
Lift safely: Cabinet is heavy; use two people for lifting and positioning.
Secure assembly: Tighten all screws and fittings securely to prevent instability.
Wall mounting: Must be anchored to wall studs to prevent tipping.

WARNING! Failure to properly secure the cabinet to the wall can result in serious injury or death from tipping. Keep small children away during assembly.

Assembly Instructions

Follow steps in order. Do not fully tighten screws until structure is aligned.

Prepare panels: Lay side panels (A, B) flat. Insert wooden dowels (J) into pre-drilled holes.
Attach top and bottom: Connect top panel (C) and bottom panel (D) to side panels using cam locks (I). Ensure arrows on cams point in correct direction.
Install back panel: Slide back panel (E) into grooves on rear of cabinet. Secure with provided screws.
Mount hinges: Attach hinges (H) to door panels (G) using screws. Then attach hinges to cabinet side panels.
Attach handles: Screw door handles (L) to doors at marked positions.
Insert shelves: Place adjustable shelves (F) onto shelf support pins inside cabinet.
Final check: Ensure all cam locks are turned to locked position. Tighten all screws. Check door alignment.

Tip: Do not overtighten screws into particleboard. Assemble on a soft surface to avoid scratching.

Installation & Mounting

The cabinet must be securely attached to wall studs.

Locate studs: Use a stud finder to locate at least two wall studs where cabinet will be mounted.
Position cabinet: With help, hold cabinet against wall in desired location. Use a level to ensure it is perfectly horizontal.
Mark drill points: Mark through the holes in the mounting brackets (K) attached to the cabinet back.
Drill pilot holes: Drill pilot holes into the marked stud locations.
Secure to wall: Use heavy-duty screws (not included, recommend 3" minimum) to fasten the cabinet brackets to the wall studs.
Final check: Gently pull on the cabinet to confirm it is firmly anchored.

CAUTION! Do not rely on drywall anchors alone. The cabinet must be screwed directly into wooden wall studs.

Adjusting Shelves

Shelves are adjustable to customize storage space.

Remove shelf: Lift shelf up slightly and pull forward to disengage from support pins.
Reposition pins: Shelf support pins can be moved to different pre-drilled holes inside the cabinet side panels.
Reinsert shelf: Place shelf onto the pins at the new desired height. Ensure it is level and fully seated.

Note: Do not exceed the maximum load of 33 lbs (15 kg) per shelf. Distribute weight evenly.

Care & Maintenance

To maintain appearance and longevity.

Cleaning: Wipe surfaces with a soft, damp cloth. Use mild soap if needed. Dry immediately.
Avoid: Abrasive cleaners, scouring pads, solvents, or excessive moisture.
Door adjustment: If doors sag or misalign, use a screwdriver to adjust the hinges. Turn the screw on the hinge to move the door in/out or up/down.

CAUTION! Never use steam cleaners or place near direct heat sources.

Specifications

Product Name: IDÅSEN
Article Number: 504.963.81
Dimensions (W x H x D): 31.5" x 74.75" x 15.75" (80 cm x 190 cm x 40 cm)
Weight: 55 lbs (25 kg)
Material: Particleboard, Fiberboard, Plastic edging, Steel hardware
Finish: White, Matte
Max. Shelf Load: 33 lbs (15 kg) per shelf
Door Swing: 90 degrees

Warranty Information

IKEA Limited Warranty: This product is covered by a 10-year limited warranty against manufacturing defects in materials and workmanship under normal household use. Proof of purchase (receipt) is required. Warranty does not cover damage from improper assembly, accidents, modification, or commercial use. For warranty service, contact your local IKEA store or visit www.IKEA.com.

Troubleshooting

Symptom	Possible Cause	Corrective Action
Cabinet wobbles	Uneven floor; Loose fittings; Not wall-mounted	Check level; Tighten all cam locks and screws; Ensure cabinet is securely anchored to wall studs.
Doors not closing evenly	Hinges misaligned	Adjust hinge screws to realign doors. Refer to hinge adjustment in Care section.
Shelf sags or is unstable	Overloaded; Shelf pins not engaged	Remove excess weight (max 33 lbs). Remove and reinsert shelf, ensuring it rests fully on all four pins.
Missing part or hardware	Packaging error	Contact IKEA customer service with your article number (504.963.81) and receipt for replacement parts.
Scratches or damage during assembly	Rough handling	Assemble on a soft blanket. Minor scratches can be touched up with a matching furniture repair pen.

Customer Support: Visit www.IKEA.com or contact your local IKEA store.