IKEA IDÅSEN 404.963.91 Shelf Unit instructions manual

The IKEA IDÅSEN 404.963.91 is a versatile shelf unit designed for home or office storage. It features a sturdy metal frame, adjustable shelves, and a modern design. Below are key sections for safety, parts list, assembly, installation, care, and warranty information.

Parts & Tools Included

Before assembly, verify all parts are present. Key components: Metal frame panels, shelves, screws, cam locks, dowels, wall attachment device, Allen key.

Safety Instructions

Read all instructions before assembly. Use caution to prevent injury or damage.

1. Assemble on a soft surface (e.g., carpet) to avoid scratching parts.
2. Use two people for lifting and positioning the unit.
3. Secure the unit to the wall using the provided bracket to prevent tipping.
4. Do not exceed the maximum weight capacity per shelf (see section 6).
5. Keep small parts away from children during assembly.

WARNING! Failure to secure the unit to the wall can result in serious injury or death from tipping. Always attach to a solid wall using suitable screws (not included).

Assembly Steps

Follow steps in order. Estimated assembly time: 30-45 minutes.

1. Prepare: Unpack all parts and lay them out. Identify each part using the included diagram.
2. Connect side panels: Insert dowel pins (D) into side panels (A1, A2). Align with corresponding holes on rear panels (A3, A4).
3. Secure frame: Use cam lock screws (C) to tighten connections between panels. Turn clockwise until snug (do not overtighten).
4. Attach base: Slide the bottom shelf (B1) into the lowest position on the frame. Ensure it rests evenly on support pins.
5. Add remaining shelves: Insert middle (B2) and top (B3) shelves into desired height positions (see section 5).
6. Install plastic caps: Press caps (G) onto the bottom of each leg to protect floors.

Tip: Keep the unit lying down until wall attachment is complete (section 4).

Installation & Leveling

Proper installation ensures stability and safety.

1. Choose location: Place the unit against a solid wall (drywall, stud, or masonry). Ensure there is space for doors/drawers to open.
2. Attach to wall:
   • Locate wall studs using a stud finder.
   • Position the wall bracket (E1) on the wall at the top rear of the unit's intended position.
   • Mark screw holes, drill pilot holes, and secure the bracket to the wall with appropriate screws (not included).
   • Lift the assembled unit upright and hook the top rear of the frame onto the bracket.
3. Level the unit: Use a spirit level on the top shelf. Adjust by placing shims under legs if the floor is uneven.

CAUTION! Do not place the unit near heat sources or in damp areas. Ensure the wall attachment is secure before loading shelves.

Adjusting Shelves

Shelves are adjustable to accommodate items of various heights.

1. Empty the shelf you wish to move.
2. Lift the shelf slightly upward to disengage it from the support pins.
3. Remove the shelf from the unit.
4. Choose new height: Align the shelf's mounting holes with the desired set of support pins inside the frame.
5. Lower the shelf onto the pins, ensuring it clicks into place and is level.
6. Test stability by applying gentle pressure.

Note: All shelves must be properly seated on at least two support pins on each side. Do not leave shelves partially engaged.

Weight Capacity

• Maximum load per shelf: 15 kg (33 lbs).
• Total unit capacity: 45 kg (99 lbs).
• Recommended distribution: Place heavier items on lower shelves to maintain a low center of gravity.
• Do not place: Aquariums, large appliances, or any item exceeding the per-shelf limit.

WARNING! Overloading shelves can cause bending, collapse, or tipping, resulting in injury or damage.

Care & Maintenance

Clean regularly to maintain appearance.

1. Metal frame: Wipe with a soft, damp cloth. Dry immediately. Do not use abrasive cleaners or solvents.
2. Shelves: Use a mild soap solution for stubborn marks. Avoid excessive moisture.
3. Inspection: Periodically check all connections, wall attachment, and shelf supports for tightness.

CAUTION! Do not use steel wool or harsh chemicals. Never spray cleaner directly onto the unit.

Disassembly & Moving

To move or store the unit, disassemble in reverse order of assembly.

1. Empty all shelves completely.
2. Remove wall attachment: Lift the unit slightly to unhook it from the bracket.
3. Lay the unit carefully on its back on a soft surface.
4. Remove shelves by lifting them out.
5. Loosen cam locks with the Allen key and separate frame panels.
6. Store all parts and hardware together for reassembly.

Tip: Place screws and small parts in a labeled bag to avoid loss.

Troubleshooting

Warranty & Support

IKEA Limited Warranty: Covers manufacturing defects for a specified period from date of purchase. Proof of purchase required.

For support:

• Visit the IKEA website: www.ikea.com
• Contact IKEA customer service: 1-888-888-4532
• Refer to your local store for spare parts or assembly assistance.

Note: Warranty does not cover damage from improper assembly, misuse, or failure to follow safety instructions (e.g., not attaching to wall).