IKEA HOVET 305.159.17 Mirror instructions manual

The IKEA HOVET 305.159.17 is a large, rectangular wall-mounted mirror designed to create a sense of space and light in any room. It features a sturdy aluminum frame, safety backing to reduce injury risk if broken, and is intended for secure mounting on solid walls. Below are key sections for safety, features, installation, setup, care, and troubleshooting.

1. Features at a Glance 2. Safety Information 3. Included Parts & Tools 4. Installation Instructions 5. Mounting & Leveling 6. Care & Cleaning 7. Specifications 8. Warranty & Support 9. Troubleshooting

Features at a Glance

Key components: Large rectangular mirror, Aluminum frame, Safety backing film, Wall mounting brackets, Fixing screws and wall plugs.

Feature	Description
Frame Material	Aluminum, powder-coated finish
Mirror Type	Clear float glass with silver backing
Safety Feature	Protective safety film on the back
Mounting System	Keyhole brackets for secure wall hanging
Intended Use	Indoor wall mounting only
Effect	Enhances light and creates an illusion of space

Safety Information

Read all instructions before assembly and installation.

Wall Requirement: Must be mounted on a solid wall (brick, concrete, or sturdy stud wall). Do not mount on plasterboard alone.
Weight Warning: Mirror is heavy. Use two people for handling and installation.
Child Safety: Keep away from play areas. Ensure it is securely mounted out of reach if necessary.
Glass Care: Avoid impacts to edges and surface. The safety backing reduces but does not eliminate risk of breakage.

WARNING! Improper installation can cause the mirror to fall, resulting in serious injury or property damage. Ensure all fixings are secure and appropriate for your wall type.

Included Parts & Tools

Check that all parts are included before starting.

Mirror: 1 unit with pre-attached brackets.
Fixing Kit: Screws and wall plugs (suitable for solid walls).
Template: 1 paper template for marking drill holes.
Required Tools (Not Included): Drill, Masonry bit (if solid wall), Stud finder (if applicable), Level, Screwdriver, Pencil, Tape measure.

Tip: For hollow walls (drywall/plasterboard), you must purchase appropriate anchors separately.

Installation Instructions

Follow these steps carefully for secure mounting.

Choose Location: Select a solid wall. Ensure no electrical wires or pipes behind intended area.
Use Template: Tape the paper template to the wall at desired height. Use a level to ensure it is perfectly horizontal.
Mark Holes: Mark the drill points through the template circles.
Drill Holes: Remove template. Drill holes at marked points to depth specified for your wall plugs.
Insert Plugs: Tap wall plugs into holes until flush with wall.
Mount Brackets (if separate): Screw the mounting brackets to the wall, leaving screw heads slightly protruding for keyhole slots.
Hang Mirror: With help, lift mirror and engage keyhole slots onto screw heads. Lower gently until secure.
Final Check: Ensure mirror is level and does not wobble. Apply gentle downward pressure to test security.

Mounting & Leveling

Proper leveling is crucial for appearance and safety.

Key Steps:

Always use a spirit level on the top edge of the mirror frame after hanging.
If adjustment is needed, slightly loosen one screw (do not remove), adjust mirror, then retighten.
The mirror should rest flat against the wall with no gaps at the top.

Recommended Height: For full-length viewing, mount so the center of the mirror is approximately at eye level (around 150-160 cm from the floor).

Care & Cleaning

To maintain appearance and longevity.

Cleaning: Use a soft, lint-free cloth. For smudges, lightly dampen cloth with water or a mild glass cleaner. Spray cleaner onto the cloth, not directly onto the mirror.
Avoid: Abrasive cleaners, scouring pads, ammonia-based products on the frame, and excessive moisture.
Frame: Wipe with a dry soft cloth. For stubborn marks, use a slightly damp cloth and dry immediately.

CAUTION! Do not use sharp objects or excessive pressure on the glass surface.

Specifications

Article Number: 305.159.17
Dimensions: Width: 120 cm, Height: 200 cm, Depth: 2.5 cm
Weight: Approximately 15 kg
Frame: Aluminum, Black/Brown finish
Glass Thickness: 4 mm
Safety Standard: Complies with applicable safety standards for mirrors.

Warranty & Support

IKEA limited warranty applies. See IKEA terms or original receipt for details.

Support: For missing parts, assembly questions, or product support:

Visit: www.ikea.com
Contact your local IKEA store.
Refer to the assembly guide included in the packaging (different from this manual).

This manual provides general instructions. Always prioritize the specific assembly guide shipped with the product.

Troubleshooting

Symptom	Possible Cause	Corrective Action
Mirror wobbles or feels loose	Wall plugs not secure / Wrong wall type	Re-mount using correct heavy-duty anchors for your wall. Ensure screws are tight.
Mirror is not level	Installation error	Loosen screws slightly, adjust mirror with level, retighten.
Brackets not aligning with holes	Template not used correctly / Wall uneven	Re-measure and re-drill holes using template carefully. Check wall flatness.
Frame scratched during assembly	Contact with hard surfaces/tools	Assemble on a soft surface (e.g., carpet, blanket). Handle with care.
Glass appears distorted at edges	Normal for large mirrors / Mounting stress	Slight distortion at extreme edges is normal. If severe, ensure mirror is not forced or twisted during hanging.

Important: If the glass is cracked or broken, do not attempt to install or use it. Contact IKEA for guidance.