IKEA HJÄLPA 094.834.14 Hinge instructions manual

The IKEA HJÄLPA 094.834.14 is a concealed hinge designed for kitchen cabinets and furniture doors. It features a 110-degree opening angle, soft-closing mechanism, adjustable in three dimensions (height, depth, and side-to-side), and is compatible with system holes. Below are key sections for safety, features, installation, adjustment, care, and troubleshooting.

1. Features at a Glance 2. Tools Required 3. Installation Steps 4. Specifications 5. Adjustment Guide 6. Mounting Plate Installation 7. Door Alignment 9. Care & Maintenance 10. Regulatory Information 11. Troubleshooting

Features at a Glance

Key components: Hinge arm, mounting plate, cup, adjustment screws, soft-closing mechanism.

Feature	Description
Opening angle	110 degrees for full cabinet access
Soft-closing	Integrated damper for quiet, gentle closing
3D adjustment	Height, depth, and side-to-side fine-tuning
Mounting plate	For attachment to cabinet frame
Cup diameter	35mm for standard system holes
Material	Steel construction with nickel plating
Compatibility	For doors 13-25mm thick
Load capacity	Suitable for doors up to 4kg
Installation	Quick mounting with screws included
Adjustment screws	Three screws for precise alignment

Tools Required

Gather necessary tools before starting installation.

Drill with 35mm Forstner bit or hinge boring bit
Phillips screwdriver (size #2)
Measuring tape
Pencil for marking
Level (for alignment verification)

WARNING! Use appropriate safety equipment (goggles) when drilling. Ensure work area is clean and well-lit.

Installation Steps

Follow these steps for proper hinge installation.

Mark hinge positions: Standard placement is 21mm from door edge, 100-120mm from top/bottom.
Drill cup hole: Use 35mm bit to drill 13mm deep hole on door interior.
Insert hinge cup: Place hinge into hole, secure with provided screws.
Attach mounting plate: Screw plate to cabinet frame at corresponding position.
Snap hinge to plate: Align hinge arm with plate and press until it clicks into place.

CAUTION! Drill carefully to avoid splintering. Do not overtighten screws.

Specifications

Article Number: 094.834.14
Type: Concealed hinge with soft-closing
Opening Angle: 110°
Cup Diameter: 35mm
Drill Depth: 13mm
Door Thickness: 13-25mm
Adjustment Range: Height: ±2mm, Depth: ±3mm, Side: ±2mm
Material: Steel, nickel-plated
Included: Hinge, mounting plate, screws (4 pcs)
Weight Capacity: Up to 4kg per hinge

Adjustment Guide

Use adjustment screws for perfect door alignment.

Height Adjustment: Turn the vertical screw (usually marked "UP/DOWN") to move door up or down.

Depth Adjustment: Turn the horizontal screw (usually marked "IN/OUT") to move door closer to or further from frame.

Side Adjustment: Turn the side screw (usually at base of hinge arm) to adjust door left or right relative to cabinet.

Make small adjustments (1/4 turn at a time) and test door operation after each change.

Mounting Plate Installation

Correct plate positioning is crucial for proper hinge function.

Mark plate position on cabinet frame: Typically 37mm from front edge.
Pre-drill pilot holes for screws to prevent wood splitting.
Secure plate with two screws, ensuring it sits flush against frame.
Verify plate is level and properly aligned with neighboring plates.

Tip: Use template or measuring jig for consistent placement across multiple cabinets.

Door Alignment

Proper alignment ensures smooth operation and aesthetic appearance.

Check gap consistency: Doors should have even gaps (2-3mm) on all sides.
Adjust height first: Ensure all doors on same cabinet are at same height.
Adjust depth: Doors should be flush with cabinet frame when closed.
Adjust side position: Ensure doors are parallel and evenly spaced.
Test opening/closing: Door should open fully and close softly without binding.

WARNING! Do not force adjustments beyond screw limits. Over-tightening can strip threads.

Care & Maintenance

Clean with dry cloth only; avoid liquids or abrasive cleaners.

CAUTION! Do not lubricate hinge mechanism. The soft-closing damper contains sealed hydraulic fluid.

Regulatory Information

IKEA HJÄLPA hinge complies with EU safety standards for furniture hardware. Tested according to EN 15570:2008 for durability. Copyright © IKEA of Sweden AB. For support, visit www.ikea.com or contact your local IKEA customer service.

Troubleshooting

Symptom	Possible Cause	Corrective Action
Door doesn't close properly	Misalignment	Adjust height/depth/side screws; check for obstructions.
No soft-closing	Damper issue	Ensure hinge is fully snapped into plate; check for damage.
Door sags	Loose screws/overload	Tighten all screws; verify weight limit (add more hinges if needed).
Hinge doesn't snap to plate	Plate misaligned	Reposition mounting plate; ensure it's flush with frame.
Uneven gaps	Incorrect adjustment	Readjust all hinges on door; use level for verification.

Replacement: If hinge is damaged, replace entire unit (not repairable).

Service: Contact IKEA customer service or visit www.ikea.com for spare parts.