IKEA HEMTRÄSK 094.771.06 Countertop instructions manual

The IKEA HEMTRÄSK 094.771.06 is a durable, pre-finished countertop designed for kitchen and bathroom applications. Made from particleboard with a moisture-resistant foil finish, it features a smooth surface, rounded front edge, and is compatible with standard IKEA cabinet systems. Below are key sections for safety, assembly, installation, care, and warranty information.

1. Product Overview & Contents 2. Safety Instructions 3. Tools Required 4. Assembly & Installation 5. Mounting to Cabinets 6. Sink & Hob Cutouts 7. Sealing & Waterproofing 8. Care & Maintenance 9. Technical Specifications 10. Warranty & Support 11. Troubleshooting

Product Overview & Contents

Key components: Pre-finished countertop, adhesive sealing strip, mounting brackets (if included), assembly instructions.

Component	Description
Countertop	Particleboard core with moisture-resistant foil finish
Adhesive sealing strip	For sealing the cut edges after installation
Mounting brackets	For securing countertop to cabinet frames (quantity varies)
Instruction manual	This document
Warning labels	Safety and care information stickers

Safety Instructions

Read all instructions before assembly and installation.

Always use at least two people to lift and position the countertop.
Ensure cabinets are level, stable, and securely anchored to the wall.
Wear safety glasses and gloves when cutting or drilling.
Keep away from open flames and high heat sources.

WARNING! Countertop is heavy; improper lifting can cause injury. Ensure work area is clean and dry.

Tools Required

Gather these tools before starting:

Measuring tape and pencil
Level (at least 24 inches)
Drill with screwdriver bits
Jigsaw with fine-tooth blade (for cutouts)
Clamps (optional, for securing during work)
Sandpaper (fine grit, for smoothing edges)
Sealant gun (if using additional silicone)

Note: Use tools appropriate for wood/laminate materials.

Assembly & Installation

Follow these steps for proper installation.

Prepare cabinets: Ensure they are level, secured to wall, and aligned.
Position countertop: Lift with two people, place gently on cabinets.
Check overhang: Standard overhang is ¾ inch (20mm) at front and sides.
Align and center: Adjust until evenly positioned on all cabinets.
Secure from below: Attach using mounting brackets into cabinet frames.

CAUTION! Do not stand or apply excessive weight on countertop before it is fully secured.

Mounting to Cabinets

Use brackets for a secure fit.

Mark bracket locations inside cabinet frames (refer to cabinet instructions).
Pre-drill pilot holes for screws (prevents splitting).
Attach brackets to cabinet frames using provided screws.
Lower countertop onto brackets and tighten screws from below.
Check stability – there should be no movement.

Tip: Do not overtighten screws, as this may damage the particleboard core.

Sink & Hob Cutouts

If cutouts are required, follow these guidelines.

Use the template provided by the sink or hob manufacturer.
Measure twice, mark cutout area clearly with pencil.
Drill starter holes inside marked corners for jigsaw entry.
Cut slowly with jigsaw, supporting the cut piece to prevent splintering.
Sand edges smooth and apply adhesive sealing strip immediately.

WARNING! Always wear eye protection and a dust mask when cutting. Ensure cut edges are fully sealed to prevent moisture damage.

Sealing & Waterproofing

Proper sealing extends countertop life.

Apply adhesive sealing strip to all cut edges immediately after cutting.
Use a silicone sealant (100% waterproof) between countertop and wall/splashback.
Seal around sink and hob cutouts with appropriate waterproof sealant.
Allow sealant to cure fully (check product instructions) before use.

Note: The pre-finished surface is moisture-resistant, but cut edges are vulnerable without sealing.

Care & Maintenance

Clean with damp cloth and mild detergent. Wipe dry immediately.

DO: Use coasters under glasses and hot pads under pots/pans.
DO NOT: Use abrasive cleaners, scouring pads, or harsh chemicals. Avoid standing water and direct heat.

CAUTION! Prolonged exposure to moisture or heat can cause warping, swelling, or surface damage.

Technical Specifications

Article Number: 094.771.06
Material: Particleboard with foil finish
Thickness: 1 ½ inches (38mm)
Moisture Resistance: Moisture-resistant foil (not waterproof)
Weight Capacity: Distributed load up to 100 lbs/sq ft when properly supported
Edge Profile: Rounded front edge
Color/Finish: As per product label

Warranty & Support

Limited warranty as per IKEA terms. Valid with proof of purchase.

For assembly help, missing parts, or warranty claims:
Visit www.ikea.com or contact your local IKEA store.
Phone support available in most regions.

Troubleshooting

Issue	Possible Cause	Solution
Countertop not level	Cabinets not level	Shim cabinets from below before securing countertop.
Gap between countertop and wall	Wall not straight	Use backsplash or trim to cover gap; apply silicone sealant.
Surface swelling or bubbling	Water exposure on cut edge	Ensure cut edges are fully sealed; dry area thoroughly; consider replacement if severe.
Movement or creaking	Insufficient brackets or loose screws	Add more brackets; tighten screws; ensure cabinets are secured to wall.
Difficulty making cutouts	Blunt blade or incorrect technique	Use sharp, fine-tooth jigsaw blade; cut slowly; support material.

Replacement Parts: Contact IKEA for sealing strips or brackets.

Support: www.ikea.com or visit your local IKEA store.