IKEA HEMNES 004.294.12 Sink Cabinet instructions manual
The IKEA HEMNES 004.294.12 is a sink cabinet designed for bathroom use, featuring a solid wood construction, water-resistant finish, integrated sink bowl (not included in all versions), adjustable legs, soft-closing doors and drawers, and pre-drilled holes for plumbing. Below are key sections for safety, parts list, assembly, installation, care, and warranty information.
Parts & Hardware Included
Check that all parts are present before starting assembly. Contact IKEA if any parts are missing.
| Part Number | Description | Quantity |
|---|
| 100001 | Cabinet side panel (left) | 1 |
| 100002 | Cabinet side panel (right) | 1 |
| 100003 | Back panel | 1 |
| 100004 | Bottom shelf | 1 |
| 100005 | Door panel | 1 |
| 100006 | Drawer front | 1 |
| HW-001 | Cam lock screws | 12 |
| HW-002 | Wooden dowels | 10 |
| HW-003 | Adjustable legs | 4 |
| HW-004 | Soft-closing hinges | 2 |
| HW-005 | Drawer runners | 1 pair |
Tools Required
You will need the following tools (not included):
- Phillips screwdriver
- Hammer (for tapping dowels)
- Hex key (Allen wrench, included)
- Level
- Tape measure
- Pencil
Tip: Work on a soft surface to avoid scratching parts.
Safety Instructions
Read all instructions before assembly. Keep children and pets away from the work area.
- Lifting: Cabinet is heavy. Use two people to lift and position.
- Stability: Secure cabinet to wall using provided wall attachment device to prevent tipping.
- Plumbing: If connecting plumbing, ensure water supply is turned off. Consult a professional if unsure.
- Tools: Use tools carefully to avoid injury.
WARNING! Failure to secure cabinet to wall can result in serious injury or death from tipping.
Step-by-Step Assembly
Follow steps in order. Do not fully tighten screws until assembly is complete.
- Step 1: Attach the adjustable legs to the bottom shelf (part 100004) using the provided screws.
- Step 2: Insert wooden dowels into the pre-drilled holes on the inside of the left side panel (100001).
- Step 3: Connect the left side panel to the bottom shelf using cam locks. Tighten with a screwdriver.
- Step 4: Repeat for the right side panel (100002).
- Step 5: Attach the back panel (100003) to the side panels using screws.
- Step 6: Install the drawer runners inside the cabinet according to the markings.
- Step 7: Attach the soft-closing hinges to the door panel (100005), then mount the door to the cabinet frame.
- Step 8: Attach the drawer front (100006) to the drawer box and insert into the runners.
- Step 9: Adjust door and drawer alignment using the screws on the hinges and runners.
CAUTION! Do not overtighten screws in particleboard to avoid stripping.
Sink & Plumbing Installation
This cabinet is designed for a drop-in sink (sink not included with model 004.294.12).
- Place the sink bowl upside down on the countertop cutout to trace the outline.
- Cut the countertop following the manufacturer's instructions for your specific sink.
- Apply a bead of silicone sealant around the cutout edge.
- Place the sink into the cutout and press down firmly. Wipe away excess sealant.
- Connect the drain and water supply lines according to local plumbing codes.
- Allow sealant to cure for 24 hours before using the sink.
Tip: We recommend hiring a professional for plumbing connections.
Adjusting & Leveling
Use the adjustable legs to level the cabinet on uneven floors.
- Place the cabinet in its final position.
- Use a level on the top surface.
- Turn the legs clockwise to raise and counterclockwise to lower until the cabinet is level.
- Once level, secure the cabinet to the wall using the wall attachment device. Locate wall studs for best support.
Note: The door and drawer soft-close mechanisms can be adjusted for tension using the screws on the side.
Care & Maintenance
To maintain the finish and functionality of your HEMNES sink cabinet.
- Cleaning: Wipe with a damp, soft cloth. Use mild soap if needed. Dry immediately.
- Avoid: Abrasive cleaners, scouring pads, ammonia-based products, or excessive water.
- Wood Care: The solid wood may expand/contract with humidity. Maintain consistent room humidity.
- Hardware: Periodically check and tighten screws and hinges if they become loose.
CAUTION! Never use steam cleaners or soak the wood.
Troubleshooting
| Issue | Possible Cause | Solution |
|---|
| Door does not close smoothly | Hinges misaligned | Adjust hinge screws in/out to realign door. |
| Drawer sticks or is uneven | Runners not aligned | Loosen runner screws, adjust drawer front, retighten. |
| Cabinet wobbles | Legs not adjusted or floor uneven | Re-level using adjustable legs. Ensure all legs touch the floor. |
| Water damage on surface | Prolonged water exposure | Dry immediately. For severe damage, sand and reapply suitable sealant. |
| Squeaking hinges or drawers | Dry moving parts | Apply a small amount of furniture wax or dry lubricant to moving parts. |
Specifications
- Product Name: HEMNES Sink Cabinet
- Article Number: 004.294.12
- Material: Solid wood, foil, ABS plastic
- Color: White stain
- Dimensions (WxDxH): 31 1/2" x 21 5/8" x 34 5/8" (80x55x88 cm)
- Sink Cutout Dimensions: Consult your sink manual. Typical cutout shown in separate diagram.
- Max Load: Top: 110 lbs (50 kg). Drawer: 22 lbs (10 kg).
- Weight: 55 lbs (25 kg)
Warranty & Support
This IKEA product is covered by a limited warranty. Refer to the IKEA warranty terms for details.
IKEA Guarantee: 10-year limited warranty for manufacturing defects.
Support: For assembly help, missing parts, or other questions:
- Visit: www.ikea.com
- Contact your local IKEA store.
- Refer to the last page of the manual for your country's customer service number.
Recycling: Dispose of packaging material responsibly. The product is recyclable at end of life.
IKEA HEMNES 004.294.12 Sink Cabinet instructions manual © - All Rights Reserved 2025