IKEA HEKTAR 702.165.44 Floor Lamp instructions manual

The IKEA HEKTAR 702.165.44 is a modern floor lamp featuring an adjustable head, sturdy metal construction, and an integrated on/off switch. Designed for use with a standard E27 bulb (max 13W LED or equivalent, not included), it provides focused lighting ideal for reading or accent illumination. Below are key sections for safety, assembly, operation, care, and troubleshooting.

1. Features at a Glance 2. Parts & Tools Included 3. Safety Instructions 4. Assembly Instructions 5. Operation & Adjustment 6. Specifications 7. Care & Maintenance 8. Troubleshooting 9. Warranty & Support

Features at a Glance

Key components: Adjustable lamp head, metal stand, stable base, integrated on/off switch, E27 bulb socket.

Feature	Description
Adjustable Head	Head can be tilted to direct light where needed
On/Off Switch	Integrated switch on the cord for easy operation
Bulb Socket	Standard E27 socket (bulb not included)
Construction	Durable metal and steel for stability
Base Design	Weighted base to prevent tipping
Cable Length	Approx. 1.8m power cord

Parts & Tools Included

Unpack and verify all parts are present before assembly.

Base: 1 piece
Stand Tube: 1 piece
Lamp Head with Shade: 1 piece
Hardware Pack: Contains screws and fasteners
Power Cord with Switch: 1 piece
Assembly Tool (if included): Allen key

NOTE: E27 bulb (max 13W LED or equivalent) is required but not included.

Safety Instructions

WARNING! To reduce the risk of fire, electric shock, or injury:

Read all instructions before assembly and use.
Unplug lamp before installing or replacing bulb, and when cleaning.
Use only with E27 bulb, max 13W LED or equivalent. Do not exceed recommended wattage.
Place lamp on a stable, level surface to prevent tipping.
Do not use outdoors or in damp locations.
Keep cord away from heated surfaces and foot traffic.
This lamp is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, unless they have been given supervision or instruction.

Assembly Instructions

Estimated assembly time: 15-20 minutes.

Prepare Workspace: Clear a flat area and lay out all parts.
Attach Base to Stand: Insert the lower end of the stand tube into the base. Secure with the provided screw(s) using the included tool.
Attach Lamp Head: Connect the lamp head to the top of the stand tube. Tighten the joint to secure, but do not over-tighten.
Route the Cord: Guide the power cord along the stand as shown in the illustration, ensuring it is not pinched.
Final Check: Ensure all connections are tight and the lamp stands upright without wobbling.

Tip: Assemble with another person for easier handling.

Operation & Adjustment

Installing the Bulb: Ensure lamp is unplugged. Screw an E27 bulb (max 13W LED) into the socket. Do not overtighten.
Power On: Plug the cord into a standard 120V AC wall outlet.
Using the Switch: Press the switch on the cord to turn the lamp ON or OFF.
Adjusting the Light: Gently tilt the lamp head to direct light. The joint is designed to hold its position.

CAUTION! The lamp head and bulb may become hot during use. Allow to cool before adjusting.

Specifications

Product Name: HEKTAR Floor Lamp
Article Number: 702.165.44
Material: Steel, Metal
Color: Black
Height: Approx. 140 cm (55 inches)
Bulb: 1 x E27 socket (max 13W LED or equivalent, not included)
Switch: Integrated on/off switch on cord
Cord Length: Approx. 1.8m (6 feet)
Voltage: 120V AC, 60Hz

Care & Maintenance

Unplug lamp before any cleaning.

Cleaning: Wipe the metal surfaces with a soft, dry cloth. For stubborn marks, use a slightly damp cloth and dry immediately.
Shade: Dust the shade gently with a soft brush or dry cloth.
Bulb Replacement: Ensure lamp is unplugged and bulb is cool. Replace with correct E27 bulb (max 13W LED).

DO NOT use abrasive cleaners, solvents, or immerse any part of the lamp in water.

Troubleshooting

Symptom	Possible Cause	Corrective Action
Lamp does not turn on	Bulb burnt out; not plugged in; switch off	Replace bulb; ensure plug is secure in outlet; check switch is ON.
Lamp flickers	Loose bulb; faulty bulb	Turn off and unplug. Ensure bulb is screwed in tightly. Try a new bulb.
Lamp wobbles	Assembly not tight; uneven floor	Check and tighten all assembly connections. Place on a level surface.
Head does not stay in position	Joint is loose	Gently tighten the adjustment joint. Do not over-tighten.
Overheating	Bulb wattage too high	Use only recommended bulb (max 13W LED). Unplug and allow to cool.

Warranty & Support

Refer to the IKEA warranty card included with your purchase for specific terms and duration. This product is designed for residential use.

For Support: Visit the IKEA website at www.ikea.com or contact your local IKEA store. Have the article number (702.165.44) ready.

Recycling: Dispose of this product and any electronic components according to local regulations. Do not dispose of with household waste.