IKEA HEKTAR 404.162.81 Floor Lamp instructions manual

The IKEA HEKTAR 404.162.81 is a modern floor lamp featuring an adjustable head, sturdy metal construction, and a fabric shade. It provides direct and indirect lighting, is designed for use with a maximum 13W LED bulb or equivalent CFL (E26/E27 base), and includes a foot switch for easy operation. Below are key sections for safety, assembly, operation, care, and troubleshooting.

1. Safety Instructions 2. Package Contents 3. Assembly Instructions 4. Specifications 5. Operation & Adjustment 6. Bulb Replacement 7. Care & Maintenance 8. Troubleshooting 9. Warranty & Support

Safety Instructions

Read all instructions before assembly and use.

  1. Use only with recommended bulb type and wattage (max 13W LED/CFL).
  2. Disconnect from power before assembly, cleaning, or bulb replacement.
  3. Place on a stable, level surface away from heat sources and water.
  4. Do not use if cord or plug is damaged.
  5. This lamp is for indoor use only.

WARNING! Risk of electric shock or fire if misused. Keep out of reach of children.

Package Contents

Ensure all parts are present before starting assembly.

PartQuantityDescription
A. Base1Weighted metal base
B. Pole sections2Metal tubes
C. Shade1Fabric shade with frame
D. Lamp head1Adjustable head with socket
E. Hardware pack1Screws, washers, Allen key
F. Foot switch1Integrated on/off switch

Assembly Instructions

Estimated assembly time: 15-20 minutes. Tools needed: Allen key (provided).

  1. Attach pole to base: Insert the bottom pole section into the base. Secure with the provided screw using the Allen key.
  2. Connect pole sections: Screw the second pole section onto the first.
  3. Attach lamp head: Connect the adjustable head to the top of the pole. Tighten the joint screw to secure.
  4. Attach shade: Slide the fabric shade over the lamp head and secure it to the frame clips.
  5. Route cord: Run the power cord down the pole and out the base opening.
  6. Insert bulb: Screw in a compatible bulb (max 13W LED/CFL, E26/E27 base). Do not overtighten.
  7. Plug in: Connect the foot switch to a standard 120V outlet.

CAUTION! Ensure all connections are tight and the lamp is stable before use.

Specifications

Operation & Adjustment

Turning On/Off: Use the foot switch on the power cord.

Adjusting Light Direction: The lamp head pivots up/down and swivels left/right. Gently move the head to direct light where needed.

Tip: For ambient lighting, point the head upward. For task lighting, direct it downward.

Bulb Replacement

  1. Turn off and unplug the lamp. Allow bulb to cool completely.
  2. Support the shade with one hand.
  3. Unscrew the old bulb counterclockwise.
  4. Screw in a new compatible bulb (max 13W LED/CFL, E26/E27 base) clockwise. Do not exceed wattage.
  5. Plug in and test.

WARNING! Never use incandescent bulbs exceeding recommended wattage, as they may overheat the shade.

Care & Maintenance

Unplug before cleaning.

CAUTION! Never immerse any part of the lamp in water.

Troubleshooting

SymptomPossible CauseCorrective Action
Lamp does not turn onNo power, faulty bulb, loose connectionCheck outlet; ensure plug is secure; replace bulb; check foot switch.
Lamp flickersLoose bulb, faulty bulbTurn off, unplug, and tighten bulb. If problem persists, try a new bulb.
Lamp is unstableAssembly not tight, uneven surfaceEnsure all screws are tightened. Place on a flat, level surface.
OverheatingBulb wattage too highImmediately turn off and unplug. Replace with a max 13W LED/CFL bulb.
Head won't stay in positionJoint screw looseTighten the pivot joint screw with the Allen key.

Warranty & Support

IKEA limited warranty applies. Refer to your IKEA warranty document for details.

For assistance:

Recycling: Dispose of the lamp and bulb according to local regulations. Many communities offer electronics recycling programs.

IKEA HEKTAR 404.162.81 Floor Lamp instructions manual © - All Rights Reserved 2025