IKEA HEKTAR 203.493.82 Work Lamp instructions manual

The IKEA HEKTAR 203.493.82 is an adjustable work lamp designed for focused task lighting. It features a flexible gooseneck arm, a stable clamp base for secure attachment to desks or shelves, an energy-efficient LED bulb, an on/off switch, and a classic industrial design. Below are key sections for safety, features, assembly, installation, operation, care, and troubleshooting.

1. Features at a Glance 2. Assembly Instructions 3. Installation & Mounting 4. Specifications 5. Controls and Operation 6. Adjusting the Lamp 7. Replacing the Bulb 8. Safety Information 9. Care & Cleaning 10. Warranty & Support 11. Troubleshooting

Features at a Glance

Key components: Adjustable gooseneck arm, Clamp base with protective pad, Integrated LED light source, On/Off switch, Steel construction with black finish.

Feature	Description
Gooseneck Arm	Flexible arm for precise directional lighting
Clamp Base	Securely attaches to surfaces up to 2.4 inches thick
LED Light Source	Energy-efficient, long-life integrated LED
On/Off Switch	Conveniently located on the lamp body
Protective Pad	Prevents damage to the mounting surface
Industrial Design	Classic black finish for a modern look

Assembly Instructions

Unpack all parts and check contents against the parts list.

Attach the gooseneck arm: Screw the threaded end of the arm into the socket on the lamp head until hand-tight.
Prepare the clamp: Ensure the protective rubber pad is correctly placed on the clamp jaw.
Connect arm to base: Insert the other end of the gooseneck arm into the clamp assembly and secure it with the provided fastener.
Check all connections: Ensure all parts are firmly attached and there is no excessive wobble.

WARNING! Do not over-tighten connections. Assemble on a soft surface to avoid scratching components.

Installation & Mounting

Choose a suitable location on a desk, shelf, or workbench.

Position the clamp: Open the clamp jaws and place them over the edge of the chosen surface (max thickness: 2.4 in / 60 mm).
Tighten the clamp: Turn the clamping screw clockwise until the lamp is firmly and securely held in place. Do not overtighten.
Adjust the angle: Bend the gooseneck arm to direct the light where needed.
Plug in the power cord: Connect the lamp to a standard 120V AC outlet.

CAUTION! Ensure the surface is stable and can support the lamp's weight. The clamp must grip firmly to prevent tipping.

Specifications

Model: HEKTAR 203.493.82
Light Source: Integrated non-replaceable LED
Color Temperature: 2700K (Warm White)
Luminous Flux: 300 lumens
Power Consumption: 4 W
Input Voltage: 120V AC, 60Hz
Arm Length: Approx. 15 inches (adjustable)
Clamp Capacity: Up to 2.4 inches (60 mm)
Material: Steel, Plastic
Color: Black

Controls and Operation

The lamp is operated via a simple on/off switch.

Switch: Located on the body of the lamp head. Press one side for ON, the other for OFF.

Adjustment: The flexible gooseneck arm allows you to point the light precisely. Gently bend the arm to the desired position. Avoid sharp bends or forcing the arm beyond its natural range.

Adjusting the Lamp

The gooseneck arm provides full directional control.

Grasp the lamp head or the arm itself.
Gently bend the arm to direct the light beam onto your work area.
The arm will hold its position once released.

Tip: For fine adjustments, make small bends along the length of the arm rather than one sharp bend at the base.

Replacing the Bulb

This model features an integrated, non-replaceable LED light source.

The LED is built into the lamp head and is not designed to be replaced by the user.
If the light fails, the entire lamp unit will need to be replaced.
The LED has a very long lifespan under normal use conditions.

WARNING! Do not attempt to open the lamp head. There are no user-serviceable parts inside. Risk of electric shock.

Safety Information

Read all instructions before use.

Use only with 120V AC, 60Hz.
This lamp is for indoor use only.
Do not use in damp or wet locations.
Do not cover the lamp or place flammable materials near it.
Ensure the clamp is securely fastened to a stable surface.
Unplug the lamp before cleaning or when not in use for extended periods.
Do not look directly into the LED light source.

Care & Cleaning

Unplug the lamp from the outlet before cleaning.

Use a soft, dry cloth to wipe the exterior surfaces.
For stubborn marks, slightly dampen the cloth with water. Do not use cleaning sprays or solvents.
Ensure the lamp is completely dry before plugging it back in.

CAUTION! Never immerse the lamp in water or other liquids. Do not use abrasive cleaners.

Warranty & Support

IKEA limited warranty applies. Refer to the IKEA warranty document included with your purchase or available at IKEA stores for specific terms and duration.

For customer service, spare parts, or more information:

Visit: www.IKEA-usa.com
Contact your local IKEA store.
Keep your receipt as proof of purchase.

Troubleshooting

Symptom	Possible Cause	Corrective Action
Lamp does not turn on	Not plugged in / Switch off / Power outage	Check plug connection. Ensure switch is ON. Check outlet with another device.
Lamp is unstable or wobbles	Clamp not tight enough / Surface too thick or slippery	Tighten the clamp screw. Ensure surface is within 2.4" limit. Check protective pad is in place.
Gooseneck arm does not hold position	Arm over-extended / Worn out	Do not bend the arm to extreme positions. If it becomes permanently loose, the lamp may need replacement.
Light is dim or flickering	Faulty LED / Loose connection	Check plug and outlet. If problem persists, the integrated LED may be failing.
Lamp gets warm	Normal operation	Some warmth is normal during use. It should not become uncomfortably hot to touch.

Disposal: Dispose of this product in accordance with local electronic waste (e-waste) regulations. Do not dispose of with household trash.