IKEA HAVSTA 092.660.24 Base Frame instructions manual

The IKEA HAVSTA 092.660.24 is a base frame component designed for use with HAVSTA storage series, providing a sturdy foundation for cabinets and shelving units. It features a powder-coated steel construction, adjustable leveling feet, pre-drilled mounting holes for secure attachment, and a modular design for flexible configuration. Below are key sections for safety, parts list, assembly, installation, adjustment, and care.

Parts Included

Check that all listed parts are present before starting assembly.

Tools Required

Gather these tools before beginning assembly.

• Phillips screwdriver
• Hammer (for wall anchors)
• Electric drill (optional, for faster installation)
• Spirit level (minimum 60cm / 24 inches)
• Pencil (for marking wall)
• Tape measure

NOTE: The included Allen key is sufficient for basic assembly, but a power drill is recommended for wall mounting.

Safety Information

WARNING! Failure to follow these instructions can result in serious injury or damage.

1. Two-person job: The frame and attached units are heavy. Always use two people for lifting and assembly.
2. Stable surface: Assemble on a clean, flat, protected surface to avoid scratching the finish.
3. Wall attachment is mandatory: To prevent tipping, especially when loaded or with children present, the base frame MUST be securely attached to a wall stud or solid masonry using the provided brackets and hardware.
4. Check load capacity: Do not exceed the maximum weight limit specified in section 7.
5. Keep hardware away from children: Small parts are a choking hazard.

Assembly Instructions

Follow these steps in order to assemble the base frame.

1. Lay out parts: Identify all parts from the list in section 2.
2. Attach leveling feet: Screw one adjustable foot into each corner of the two main horizontal beams (Part 100001). Hand-tighten for now.
3. Connect side supports: Position the four vertical uprights (Part 100002) between the two horizontal beams. Align the pre-drilled holes.
4. Insert cross braces: Fit the two stabilizing bars (Part 100003) diagonally between the side supports, as shown in the diagram (not pictured here). This adds rigidity.
5. Secure all joints: Using the provided Allen key (100008) and M6 screws (100006), tighten all connections firmly. Ensure the frame is square before final tightening.
6. Attach mounting brackets: Fix the two L-shaped mounting brackets (100005) to the rear of the frame's top horizontal beam, near the ends.

Tip: Do not fully tighten the leveling feet until the frame is in its final position and you are ready to level it.

Installation to Wall

This step is critical for stability and safety.

1. Position the frame: With help, move the assembled frame to its desired location against the wall.
2. Mark bracket holes: Use a pencil to mark the screw hole locations on the wall through the slots in the mounting brackets.
3. Locate wall studs: Use a stud finder. For solid walls (brick/concrete), mark for anchor placement.
4. Drill pilot holes: Drill holes at your marks, sized appropriately for the wall anchors (for solid walls) or slightly smaller than the screw diameter for wood studs.
5. Insert wall anchors: If needed, tap the provided wall anchors (100007) into the holes in solid walls.
6. Secure the frame: Hold the frame firmly against the wall. Insert screws through the brackets and into the wall/studs. Tighten securely.

CAUTION! Ensure the wall can support the intended load. If unsure, consult a professional.

Leveling & Adjustment

Even on uneven floors, you can achieve a stable, level installation.

1. Place a spirit level along the top of the frame, both front-to-back and side-to-side.
2. Turn the adjustable feet clockwise to raise that corner or counter-clockwise to lower it.
3. Re-check the level after each adjustment.
4. Once perfectly level, use a wrench (not provided) to gently tighten the lock nut on each foot (if present) to prevent it from turning later. Do not overtighten.

Note: The frame must be level before attaching any HAVSTA cabinets or shelves.

Weight Capacity

• Maximum distributed load: 80 kg (176 lbs) across the entire frame.
• Maximum point load (per shelf/cabinet): 25 kg (55 lbs).
• Dynamic load (e.g., doors opening, items being placed): Considered within the static limits. Avoid sudden impacts.

WARNING! Exceeding these limits can cause frame failure, tipping, or collapse. Distribute weight evenly.

Compatible Components

The HAVSTA 092.660.24 Base Frame is designed to work with the following IKEA HAVSTA series items:

Follow the assembly instructions for each specific component when attaching them to the base frame.

Care & Maintenance

To ensure long-lasting performance and appearance:

• Cleaning: Wipe with a soft, damp cloth. Use a mild detergent if necessary. Dry immediately.
• Avoid: Abrasive cleaners, scouring pads, or harsh chemicals which can damage the powder coat.
• Periodic check: Every 6 months, check that all screws and wall attachments are tight. Re-level if necessary.
• Inspect leveling feet: Ensure they remain firmly in contact with the floor and have not loosened.

CAUTION! Do not use the frame as a step ladder or seat.

Troubleshooting

Missing Parts? Contact IKEA customer service with your article number (092.660.24) and proof of purchase.

Need Help? Visit www.ikea.com or your local IKEA store for assembly support.