IKEA HAUGA 304.072.96 3 Drawer Chest instructions manual

The IKEA HAUGA 304.072.96 is a 3-drawer chest designed for bedroom storage, featuring a clean Scandinavian design, smooth-gliding drawers, and durable construction. Made from particleboard, fiberboard, and plastic, it requires assembly and includes all necessary hardware. Below are key sections for safety, parts list, assembly instructions, care, and warranty information.

1. Parts & Hardware Included 2. Safety Instructions 3. Assembly Instructions 4. Product Specifications 5. Drawer Installation & Adjustment 6. Care & Maintenance 7. Wall Attachment 8. Troubleshooting 9. Warranty & Support

Parts & Hardware Included

Before assembly, verify all parts are present. Contact IKEA if any items are missing.

Part Description	Quantity	Image Reference
Chest Side Panel	2	A
Chest Back Panel	1	B
Chest Top Panel	1	C
Chest Bottom Panel	1	D
Drawer Front	3	E
Drawer Side	6	F
Drawer Bottom	3	G
Drawer Runner (left)	3	H
Drawer Runner (right)	3	I
Cam Lock Screw	10	1
Wood Dowel	10	2
Drawer Knob	3	3
Wall Attachment Kit	1 set	4

Safety Instructions

Read all instructions before assembly. Use on a flat, stable surface.

Choking Hazard: Small parts included; keep away from children under 3 years.
Tip-Over Hazard: Furniture can tip over. Always use the included wall attachment device to secure to wall.
Weight Limit: Do not exceed 33 lbs (15 kg) per drawer.
Assembly: Use two people for assembly; follow steps in order.
Tools Required: Phillips screwdriver (not included).

WARNING! Serious or fatal crushing injuries can occur from furniture tip-over. Always secure furniture to wall.

Assembly Instructions

Assemble on a soft surface to avoid scratching. Follow numerical order on instruction sheet.

Step 1 - Frame: Attach side panels (A) to bottom panel (D) using dowels (2) and cam locks (1).
Step 2 - Back Panel: Secure back panel (B) to frame with screws provided.
Step 3 - Top Panel: Attach top panel (C) to side panels using dowels and cam locks.
Step 4 - Drawer Runners: Install left (H) and right (I) runners inside cabinet as marked.
Step 5 - Drawer Box: Assemble drawer sides (F) to front (E) and back, insert drawer bottom (G).
Step 6 - Drawer Installation: Slide drawer onto runners; ensure smooth movement.
Step 7 - Knobs: Attach knobs (3) to drawer fronts.

Tip: Do not fully tighten cam locks until all parts are aligned.

Product Specifications

Product Name: HAUGA 3-drawer chest
Article Number: 304.072.96
Dimensions: Width: 31 ½" (80 cm), Height: 37" (94 cm), Depth: 18 ⅛" (46 cm)
Drawer Dimensions: Interior: W 28 ¾" x D 16 ½" x H 6 ¼" (approx.)
Weight: 55 lbs (25 kg)
Max Load/Drawer: 33 lbs (15 kg)
Materials: Particleboard, Fiberboard, Plastic, Steel
Finish: White, Ash veneer
Country of Origin: Designed in Sweden, Made in [varies]

Drawer Installation & Adjustment

Drawers use roller runners for smooth operation.

Align drawer with installed runners.
Push drawer into opening until it clicks into place.
To remove: Pull drawer fully out, press release tabs on both sides of runner, lift drawer out.
Adjustment: If drawer is uneven, loosen screws on runner slightly, adjust height, retighten.
Sticking Drawer: Check for obstructions; ensure runners are clean and parallel.

Note: Do not force drawer; it should glide smoothly when properly installed.

Care & Maintenance

Clean with a damp cloth and mild detergent. Wipe dry immediately.

Surface: Use soft cloth; avoid abrasive cleaners, scouring pads, or solvents.
Drawers: Remove contents before moving chest. Do not overload.
Environment: Avoid direct sunlight, high humidity, and heat sources to prevent warping.

CAUTION! Do not use wax or polish; may damage finish.

Wall Attachment

CRITICAL: To prevent tip-over, secure chest to wall using provided kit.

Locate solid wall stud using stud finder.
Position chest against wall in desired location.
Attach wall bracket to stud using screws (not always included with chest; may require suitable wood screws).
Attach corresponding bracket to back of chest (pre-drilled holes).
Connect chest bracket to wall bracket.
Check stability; chest should not tilt forward when drawers are open.

WARNING! If you cannot attach to wall, do not use this chest. Use only with wall attachment.

Troubleshooting

Issue	Possible Cause	Solution
Drawer sticks or won't close	Misaligned runner, overloaded, obstruction	Remove drawer, check alignment, clear debris, reduce weight.
Wobbly chest	Uneven floor, loose connections	Place on level surface; tighten all cam locks and screws.
Drawer front uneven	Knob installation, runner height	Adjust knob; loosen runner screws, align drawer front, retighten.
Cam lock won't tighten	Dowel not fully inserted, cross-threaded	Disassemble, ensure dowel is seated, re-engage cam lock.
Missing part	Packaging error	Contact IKEA customer service with article number (304.072.96).

Warranty & Support

IKEA limited warranty applies. See IKEA terms or warranty card for details.

Warranty Period: Varies by country; typically 1-10 years for materials and manufacturing defects.
Support: For missing parts, assembly help, or returns, contact IKEA.
Contact: Visit www.ikea.com or your local IKEA store.
Recycling: Disassemble for recycling. Check local regulations for disposal of particleboard.

Note: This manual is a guide. Always refer to the latest instructions included with product.