IKEA HAUGA 204.592.38 6 Drawer Dresser instructions manual

The IKEA HAUGA 204.592.38 is a 6-drawer dresser from the HAUGA series, designed for bedroom storage. It features a modern design with six spacious drawers, sturdy construction, and a clean finish. The dresser requires assembly and comes with all necessary hardware and an illustrated instruction manual. Below are key sections for safety, parts list, assembly steps, care instructions, and warranty information.

1. Parts & Hardware Included 2. Tools Required 3. Safety Instructions 4. Assembly Steps 5. Drawer Installation 6. Leveling & Stability 7. Care & Maintenance 8. Product Specifications 9. Warranty & Support 10. Troubleshooting

Parts & Hardware Included

Before assembly, verify all parts are present. Key components: Dresser frame panels, drawer fronts, drawer sides/bottoms, drawer runners, back panel, screws, cam locks, dowels, and wall attachment device.

Part Description	Quantity	Image Ref.
Dresser top panel	1	A
Dresser side panels	2	B
Drawer fronts (various sizes)	6	C
Drawer bottom panels	6	D
Drawer runner sets	6 pairs	E
Back panel (fiberboard)	1	F
Cam locks + screws	10	G
Wooden dowels	12	H
Wall attachment device	1 set	I

Tools Required

Tools not included; gather before starting.

Phillips screwdriver (medium size).
Hammer (for tapping dowels).
Level (optional, for final adjustment).
Pencil (for marking if needed).

NOTE: Power drill can be used but set to low torque to avoid damaging parts.

Safety Instructions

Read all instructions before assembly. Ensure a clean, spacious work area.

Always assemble on a soft surface (carpet/blanket) to prevent scratches.
Use two people for lifting and positioning larger panels.
Secure dresser to wall using provided anti-tip device to prevent tipping.
Keep small hardware away from children and pets.

WARNING! Unsecured dressers can tip over and cause serious injury. Always attach to wall.

Assembly Steps

Follow numerical order in instruction booklet. Estimated assembly time: 60-90 minutes.

Frame Construction: Connect side panels to top using cam locks and dowels. Ensure all cam locks are fully tightened.
Internal Supports: Attach horizontal supports between side panels at marked positions.
Back Panel: Place dresser face down on soft surface. Align back panel and secure with provided screws.
Drawer Runner Installation: Attach runner halves to dresser interior sides at each drawer level.
Base Installation: Attach base plinth or feet to bottom of dresser.

Tip: Do not fully tighten all screws until entire frame is assembled to allow for adjustments.

Drawer Installation

Assemble drawers before inserting into frame.

Drawer Box: Connect drawer front, sides, and back using cam locks/dowels. Slide drawer bottom into grooves.
Runner Attachment: Attach other half of drawer runners to drawer sides.
Testing: Ensure drawers slide smoothly before attaching fronts.
Drawer Front Alignment: Insert drawer into frame. Align front with frame opening and secure from inside using screws.
Final Check: Open and close each drawer to verify smooth operation and even gaps.

NOTE: Adjust drawer front alignment by loosening screws, repositioning, and retightening.

Leveling & Stability

Ensure dresser is stable and level on floor.

Place dresser in its final location.
Use a level to check from front to back and side to side.
Adjust feet (if adjustable) or place shims under base as needed.
Wall Attachment (CRITICAL): Locate wall stud(s). Attach anti-tip bracket to wall stud using hardware not included (screws for stud). Attach other part of bracket to dresser back panel. Tighten securely.

WARNING! Never place heavy items (e.g., TV) on top of dresser. Use only for clothing and light items.

Care & Maintenance

To maintain appearance and function.

Cleaning: Wipe with a damp cloth and mild detergent. Dry immediately. Do not use abrasive cleaners.
Drawers: Periodically check runner screws for tightness. Clean runners with a dry cloth if sliding becomes stiff.
Surface Protection: Use coasters or mats under lamps or decorative items to prevent scratches.

CAUTION! Avoid excessive moisture and direct heat sources (radiators).

Product Specifications

Series: HAUGA
Article Number: 204.592.38
Dimensions (W x H x D): Approx. 120 cm x 90 cm x 48 cm (47 1/4" x 35 3/8" x 18 7/8")
Weight: Approx. 45 kg (99 lbs) (packaged)
Material: Particleboard, Fiberboard, Plastic, Steel
Finish: White stained oak veneer/White
Drawer Slide Type: Side-mounted runners with soft-close mechanism
Max Load per Drawer: Refer to label inside drawer (typically 15-20 kg)

Warranty & Support

IKEA limited warranty applies. See IKEA terms or warranty card for details.

Missing Parts? Contact IKEA customer service with article number (204.592.38) for replacement parts.

Assembly Service: Available for purchase in-store or online.

Support: Visit www.ikea.com or your local IKEA store. Keep your receipt as proof of purchase.

Troubleshooting

Issue	Possible Cause	Solution
Drawer sticks or doesn't close smoothly	Misaligned runners or overfilled drawer	Check runner alignment; ensure nothing obstructs slide; redistribute weight in drawer.
Dresser wobbles	Uneven floor or loose connections	Level the dresser with shims; tighten all cam locks and frame screws.
Cam lock won't tighten	Dowel not fully inserted or cross-threaded	Disassemble step, ensure dowel is seated properly, re-engage cam lock.
Gaps between panels	Parts not fully joined during assembly	Check all connection points are flush; tighten cams completely.
Missing hardware	Packaging error	Contact IKEA customer service with article number for replacement kit.

Safety Reminder: Dresser must be secured to wall with provided device to prevent tipping hazard.

Recycling: Dispose of packaging materials according to local regulations.