IKEA HASSLARP 394.548.15 Door instructions manual

The IKEA HASSLARP 394.548.15 is a door designed for specific IKEA cabinet frames, featuring a clean, modern design with adjustable hinges for precise alignment. This manual provides essential information for safety, assembly, installation, adjustment, care, and troubleshooting to ensure proper function and longevity.

1. Parts Included 2. Tools Required 3. Safety Information 4. Assembly & Installation 5. Hinge Adjustment Guide 6. Care & Maintenance 7. Troubleshooting 8. Specifications & Compliance

Parts Included

Before starting, verify all components are present.

Part Description	Quantity	Image Reference
HASSLARP Door Panel	1	A
Concealed Hinges (with screws)	2 or 3*	B
Mounting Plates	2 or 3*	C
Door Handles (if included)	1 set	D
Assembly Instructions	1	-

*Quantity depends on door height. Taller doors typically require 3 hinges.

Tools Required

You will need the following tools (not included):

#2 Phillips screwdriver
4mm Allen key (often provided with hinges)
Pencil
Tape measure
Level (recommended)

Safety Information

WARNING! To prevent serious injury or damage:

Secure Workspace: Assemble on a clean, flat, stable surface covered with a soft cloth to prevent scratches.
Lifting: The door panel can be heavy and awkward. Use proper lifting techniques or ask for assistance.
Secure Mounting: Ensure the cabinet frame is securely attached to the wall according to IKEA's frame instructions before hanging the door.
Child Safety: Keep small parts (screws, hinges) away from children to avoid choking hazards.

Assembly & Installation

Follow these steps to attach the door to your IKEA cabinet frame.

Prepare the Frame: Ensure the cabinet frame is level and securely installed. Identify the pre-drilled holes for the hinge mounting plates.
Attach Mounting Plates: Align the mounting plates (Part C) with the holes on the inside of the cabinet frame. Secure them using the provided screws. Do not fully tighten yet.
Attach Hinges to Door:
- Place the door face down on a protected surface.
- Position the hinges (Part B) on the back of the door according to the template or measurements in the frame manual (typically 22mm from top/bottom edge for standard doors).
- Use the provided screws to attach the hinges to the door. Tighten securely.
Hang the Door:
- Lift the door and align the hinge arms with the mounting plates on the cabinet.
- Engage the hinges by pressing the door until you hear a click or feel it lock into place.
Initial Check: Open and close the door gently. It should swing smoothly. Proceed to fine-tuning.

Hinge Adjustment Guide

Modern IKEA hinges allow adjustment in three dimensions. Use the Allen key for adjustments.

Adjustment Type	Screw/Lever Location	Effect
Height (Up/Down)	Vertical screw on mounting plate	Raises or lowers the entire door relative to the cabinet.
Depth (In/Out)	Horizontal screw on hinge arm	Moves the door closer to or farther from the cabinet frame.
Side (Left/Right)	Screw at the base of the hinge cup (on door)	Shifts the door left or right to align edges with neighboring doors or frame.

Adjustment Order: 1. Depth, 2. Height, 3. Side-to-Side. Make small increments (1/4 turn) and test frequently.

Care & Maintenance

Proper care will maintain the appearance of your door.

Cleaning: Wipe with a damp, soft cloth. Use a mild detergent if needed. Dry immediately with a clean cloth.
Avoid: Abrasive cleaners, scouring pads, harsh chemicals, or excessive water.
Hinges: Periodically check hinge screws for tightness. Do not lubricate hinges.

CAUTION! Never use steam cleaners on the door surface.

Troubleshooting

Problem	Possible Cause	Solution
Door does not close flush	Depth adjustment incorrect	Turn the depth screw on the hinge arm to move the door inward.
Door is uneven (top/bottom)	Height misalignment	Adjust the vertical screw on the mounting plate for the high side.
Gap between doors is uneven	Side-to-side misalignment	Adjust the side screw on the hinge cup to shift the door left or right.
Door sags or feels loose	Hinge screws loose	Tighten all screws connecting the hinge to the door and the mounting plate to the frame.
Door scrapes against frame	Frame not level or door misaligned	Check cabinet frame level. Use height and side adjustments to center the door in the opening.

Specifications & Compliance

Product Name: HASSLARP
Article Number: 394.548.15
Type: Cabinet Door
Intended Use: For use with specified IKEA cabinet frames.
Materials: Particleboard, foil, plastic edging. (Refer to product label for exact materials).
Warranty: Refer to the IKEA guarantee for terms and conditions.
Compliance: Manufactured according to applicable furniture safety standards.

For missing parts or further assistance, contact IKEA customer service or visit the IKEA website with your article number.