IKEA GODMORGON 494.893.34 Sink Cabinet instructions manual

The IKEA GODMORGON 494.893.34 is a bathroom sink cabinet designed for storage and functionality. It features a durable construction, water-resistant surfaces, adjustable legs, soft-closing doors/drawers, pre-drilled holes for plumbing, and assembly hardware included. Below are key sections for safety, parts list, assembly, installation, care, and warranty.

Parts & Hardware List

Key components: Cabinet frame, doors/drawer fronts, back panel, adjustable legs, hinges, drawer runners, screws, cam locks, dowels, installation template.

Safety Instructions

Read all instructions before assembly. Ensure a clean, spacious work area.

1. Use proper tools: Phillips screwdriver, hammer, level, pencil.
2. Lift with care: Cabinet parts can be heavy; use two people.
3. Secure during assembly: Place on a soft surface to avoid scratches.
4. Keep hardware away from children: Small parts are a choking hazard.

WARNING! Ensure cabinet is securely anchored to the wall if provided with anti-tip hardware to prevent tipping, especially when drawers are fully extended.

Assembly Steps

Follow numerical order in assembly guide illustrations.

1. Attach adjustable legs to the cabinet base panel.
2. Assemble the cabinet frame by connecting side, top, and bottom panels using cam locks and dowels.
3. Install the back panel to square and reinforce the frame.
4. Mount drawer runners inside the cabinet according to markings.
5. Assemble the drawer box and attach the drawer front.
6. Attach hinges to the doors, then mount doors to the cabinet frame.
7. Adjust doors and drawers for alignment and smooth operation.

CAUTION! Do not overtighten screws as this may damage the particleboard. Hand-tighten until snug.

Specifications

• Model: GODMORGON 494.893.34
• Color/Finish: As specified (e.g., white, gray, oak effect).
• Dimensions (HxWxD): Approximately 32" H x 24" W x 22" D (verify with product label).
• Material: Particleboard with foil/laminate, ABS edges.
• Weight Capacity: Drawers and shelves designed for typical bathroom items.
• Adjustable Legs: Range approximately 4-5 inches.
• Required Tools: Phillips screwdriver, hammer, level, pencil.
• Included Hardware: Yes, all necessary screws, dowels, cam locks.

Installation & Levelling

Position the assembled cabinet in its final location before securing.

1. Place cabinet: Move cabinet to desired spot in bathroom.
2. Adjust legs: Use a level on top of the cabinet. Turn legs to raise or lower until perfectly level in all directions.
3. Mark wall anchor points: Use the provided template or mark through holes in the cabinet back.
4. Secure to wall (if applicable): Drill pilot holes, insert wall plugs, and screw cabinet to wall studs for stability.
5. Final check: Ensure doors and drawers open freely without hitting walls or other obstacles.

Tip: Leave a small gap between the cabinet and wall for plumbing connections.

Connecting Plumbing

The sink (not included) is installed on top of the cabinet. Plumbing runs through the cabinet.

1. Prepare cutouts: Use the provided template to mark holes on the cabinet top/back for water supply lines and drainpipe.
2. Cut holes: Use a hole saw or jigsaw to create clean openings. Wear safety glasses.
3. Install sink: Follow the sink manufacturer's instructions to mount and seal the sink to the cabinet top.
4. Connect pipes: A plumber should connect the P-trap, drain, and water supply lines through the cabinet.

WARNING! Ensure all plumbing connections are tight and leak-free before placing items inside the cabinet. Check local plumbing codes.

Door & Drawer Adjustment

Doors and drawers feature soft-close mechanisms and are adjustable.

• Door Height: Loosen the screws on the hinge arm attached to the cabinet, move door up/down, retighten.
• Door Depth: Turn the screw on the hinge cup (inside the door) to move the door closer to or further from the frame.
• Door Sideways: Adjust the screw on the side of the hinge arm to align doors left/right.
• Drawer Alignment: Locate adjustment screws on the sides of the drawer runners to adjust height and tilt.

Note: Make small adjustments and test frequently.

Care & Maintenance

Clean with a damp, soft cloth using mild soapy water. Wipe dry immediately.

DO NOT: Use abrasive cleaners, scouring pads, strong chemicals, or excessive water. Avoid direct heat sources.

Periodically check and tighten hinges, runners, and legs if necessary.

Warranty Information

IKEA limited warranty applies. Refer to the IKEA warranty document included with your purchase or available at IKEA stores and www.ikea.com. Warranty typically covers material and manufacturing defects under normal use for a specified period. Proof of purchase is required.

Troubleshooting

Support: Visit www.ikea.com or contact your local IKEA store for assembly advice or spare parts.