IKEA GLYPEN 704.423.92 Faucet instructions manual

The IKEA GLYPEN 704.423.92 is a single-lever kitchen faucet designed for easy installation and operation. It features a pull-out spray head with multiple spray patterns, a ceramic disc cartridge for smooth and durable operation, a 360-degree swivel spout, and a brushed stainless steel finish. Below are key sections for safety, features, installation, operation, maintenance, and troubleshooting.

1. Features at a Glance 2. Installation 3. First-Time Setup 4. Specifications 5. Controls and Operation 6. Connecting to Water Supply 7. Using the Spray Head 8. Maintenance & Cleaning 9. Regulatory Information 10. Troubleshooting

Features at a Glance

Key components: Single-lever handle, Pull-out spray head with hose, Ceramic disc cartridge, Swivel spout, Mounting hardware, Water supply connectors.

Feature	Description
Single-lever handle	Controls both water temperature and flow rate
Pull-out spray head	Extends for flexible use; includes stream and spray patterns
Ceramic disc cartridge	Ensures smooth operation and long-lasting durability
360-degree swivel spout	Allows easy access to all areas of the sink
Brushed stainless steel finish	Resistant to corrosion and fingerprints
Mounting hardware	Includes all necessary nuts, washers, and screws for installation
Water supply connectors	Includes flexible hoses for hot and cold water connections
Aerator	Reduces splashing and conserves water
Hose weight	Keeps hose retracted when not in use
Docking mechanism	Secures spray head in place when not in use

Installation

Unpack and inspect all components. Ensure you have the necessary tools: adjustable wrench, plumber's tape, bucket, and cloth.

Shut off water supply: Turn off both hot and cold water valves under the sink.
Remove old faucet (if applicable): Disconnect supply lines and remove mounting nuts.
Prepare sink: Clean the mounting area thoroughly.
Install faucet: Insert faucet through mounting hole, secure from below with mounting hardware.
Connect water supply: Attach flexible hoses to corresponding hot and cold valves using plumber's tape.
Check for leaks: Turn water supply back on slowly and inspect all connections.

WARNING! Ensure water supply is completely shut off before beginning installation to prevent flooding. Tighten connections securely but do not overtighten.

First-Time Setup

After installation, perform initial setup for optimal operation.

Flush the system: Run both hot and cold water for 2-3 minutes to clear any debris from lines.
Test handle operation: Move lever left/right for temperature, up/down for flow. Operation should be smooth.
Test spray head: Pull out head, test stream and spray patterns, ensure it retracts properly.
Check swivel: Rotate spout 360 degrees to ensure smooth movement without obstruction.
Adjust hose weight (if needed): Ensure hose retracts fully when spray head is released.

CAUTION! Be careful of hot water during testing. Allow water to run until it reaches desired temperature.

Specifications

Model: GLYPEN 704.423.92
Type: Single-lever kitchen faucet with pull-out spray
Finish: Brushed stainless steel
Spout Height: 9.8 inches (250 mm)
Spout Reach: 9.4 inches (240 mm)
Hose Length: 59 inches (1500 mm)
Cartridge: Ceramic disc
Flow Rate: 1.8 GPM (6.8 L/min) at 60 psi
Water Connections: 3/8" compression fittings
Mounting Holes: Single hole or 3-hole (with deck plate)
Warranty: Limited 10-year warranty

Controls and Operation

Single lever controls both temperature and flow. Front of faucet: Lever, Spray head docking position.

Lever Operation: Move lever up to increase flow, down to decrease. Move left for cooler water, right for warmer.

Spray Head: Pull to extend. Button on spray head switches between stream (for filling) and spray (for rinsing). Release to retract - hose weight will pull it back into place.

Swivel Spout: Rotate spout left or right to direct water where needed. Spout rotates 360 degrees.

Connecting to Water Supply

Standard 3/8" compression fittings for hot and cold water lines.

Shut off main water supply before connecting.
Use plumber's tape on all threaded connections to prevent leaks.
Connect hot water line to left valve (typically marked with red).
Connect cold water line to right valve (typically marked with blue).
Hand-tighten connections first, then use adjustable wrench for final quarter turn.
Turn water supply back on slowly and check for leaks.

Tip: Keep a bucket and cloth handy during connection to catch any residual water.

Using the Spray Head

Spray head offers two modes: Stream and Spray.

To extend: Pull spray head from docking position.
To change mode: Press button on spray head to toggle between stream (solid flow) and spray (wider, softer flow).
To retract: Release spray head - hose weight will automatically retract it.
For difficult retraction: Ensure hose is not twisted or caught on objects under sink.
Cleaning spray head: Remove aerator periodically to clean mineral deposits.

WARNING! Do not pull spray head with excessive force. Do not let hose kink or twist during use.

Maintenance & Cleaning

Regular maintenance ensures long-lasting performance.

Daily cleaning: Wipe with soft, damp cloth. Dry with soft cloth to prevent water spots.
Deep cleaning: Use mild soap and water. Avoid abrasive cleaners or scouring pads.
Aerator cleaning: Remove aerator every 3-6 months, soak in vinegar to remove mineral deposits, rinse thoroughly.
Spray head cleaning: If spray pattern becomes uneven, remove and clean spray head screen.
Cartridge maintenance: If lever becomes stiff, contact IKEA for cartridge replacement.

CAUTION! Never use harsh chemicals, bleach, or abrasive cleaners. Do not use steel wool or scouring pads.

Regulatory Information

Complies with ASME A112.18.1/CSA B125.1 plumbing standards. Meets EPA WaterSense criteria for water efficiency. Lead-free compliant according to Safe Drinking Water Act. For support, visit www.ikea.com or contact IKEA customer service at 1-888-888-4532. This product is covered by IKEA's limited 10-year warranty. See warranty card for details.

Troubleshooting

Symptom	Possible Cause	Corrective Action
Low water pressure	Clogged aerator	Remove and clean aerator; soak in vinegar if mineral deposits present.
Spray head doesn't retract	Hose twisted or weight missing	Check under sink for obstructions; ensure hose weight is properly installed.
Leaking from base	Loose connections	Tighten mounting nuts; check O-rings and seals.
Handle is stiff	Cartridge issue	Contact IKEA for cartridge replacement under warranty.
Water temperature inconsistent	Supply line issues	Check hot water heater; ensure both supply valves are fully open.
Spray pattern uneven	Clogged spray head	Remove and clean spray head screen; remove debris.
Dripping from spout	Worn cartridge	Replace ceramic disc cartridge (contact IKEA for parts).

Reset: For minor issues, shut off water supply, disconnect and reconnect hoses, then turn water back on.

Service: 1-888-888-4532; www.ikea.com