IKEA GLYPEN 094.408.77 Faucet instructions manual

The IKEA GLYPEN 094.408.77 is a single-lever kitchen faucet designed for easy installation and operation. It features a pull-out spray head, ceramic disc cartridge for smooth temperature and flow control, durable metal construction, and a sleek design to complement modern kitchens. Below are key sections for safety, features, installation, operation, maintenance, and troubleshooting.

Features at a Glance

Key components: Single-lever handle, pull-out spray head with hose, ceramic disc cartridge, aerator, mounting hardware, and flexible supply lines.

Installation

Unpack and inspect all components. Ensure you have necessary tools: adjustable wrench, basin wrench, plumber's tape, and bucket.

1. Prepare sink: Turn off water supply valves under sink; open faucet to drain remaining water.
2. Mount faucet: Insert faucet through sink hole; secure from below with mounting hardware provided.
3. Connect supply lines: Attach hot and cold flexible lines to corresponding water supply valves; use plumber's tape on threads.
4. Connect spray hose: Attach pull-out hose to faucet body and secure.
5. Check connections: Tighten all connections; avoid over-tightening.
6. Test for leaks: Turn on water supply slowly; check for leaks at all connections.

WARNING! Ensure water supply is off before installation. If unsure, consult a professional plumber.

First-Time Setup

After installation, perform initial setup for optimal operation.

1. Flush faucet: Run water for 2-3 minutes to clear any debris from lines.
2. Check spray function: Pull out spray head; test stream and spray modes.
3. Adjust handle tension: If handle feels loose or tight, adjust tension screw (if applicable).
4. Set temperature limit: Some models allow adjustment of maximum hot water temperature via limiter under handle.

CAUTION! Hot water can cause burns. Set temperature limiter appropriately, especially in households with children.

Specifications

• Model: GLYPEN 094.408.77
• Type: Single-lever kitchen faucet with pull-out spray
• Finish: Chrome or matte black (as per model)
• Spray Hose Length: Approximately 59 inches (150 cm)
• Maximum Flow Rate: 1.8 GPM (gallons per minute) at 60 psi
• Cartridge: Ceramic disc, 1/4-turn operation
• Connection Size: Standard 1/2-inch IPS threads
• Warranty: Limited lifetime warranty (see documentation)
• Compliance: Meets ASME A112.18.1/CSA B125.1 standards
• Water Requirements: Minimum pressure 20 psi, maximum 80 psi

Controls and Operation

Handle Controls: Lift handle to start water flow; move left for hot, right for cold. Push down to stop.

Spray Head: Pull down to extend; release to retract. Press button on head to switch between stream (for filling) and spray (for rinsing).

Temperature Memory: The ceramic cartridge maintains temperature setting when handle is returned to same position. Aerator: Reduces splashing and conserves water; can be removed for cleaning. Handle Tension Adjustment: Some models feature a tension adjustment screw under the handle cap to customize lever feel.

Connecting to Water Supply

Ensure proper connection to avoid leaks and ensure performance.

1. Shut off main water supply or under-sink valves.
2. Use provided flexible hoses; connect hot (usually left valve) and cold (right valve).
3. Wrap male threads with plumber's tape clockwise.
4. Hand-tighten connections, then use wrench for additional quarter turn.
5. For pull-out hose, ensure it is not kinked and has free movement.

Tip: Place a bucket under connections during installation to catch any residual water.

Using the Faucet

Daily operation guidelines for best performance.

1. Starting water: Lift handle upward; adjust temperature by moving left/right.
2. Using spray head: Pull down to extend; press mode button to switch between stream and spray.
3. Stopping water: Push handle down firmly until flow stops.
4. Retracting hose: Gently guide spray head back; it should retract automatically.
5. Aerator cleaning: If flow reduces, unscrew aerator and rinse under water to remove debris.
6. Temperature adjustment: For consistent temperature, move handle gradually.

WARNING! Do not force handle; excessive force can damage cartridge. Avoid pulling spray hose at extreme angles.

Maintenance & Care

Regular maintenance ensures longevity and performance.

Cleaning: Wipe with soft, damp cloth and mild soap. Avoid abrasive cleaners or scouring pads. Aerator Cleaning: Remove every 3-6 months; soak in vinegar to dissolve mineral deposits. Spray Head Nozzles: Rub rubber nozzles with finger to clear debris. Cartridge: If handle becomes stiff or leaks, cartridge may need replacement (contact IKEA support). Hose: Periodically check hose for kinks or damage; ensure retraction is smooth.

CAUTION! Do not use harsh chemicals (bleach, acids) as they can damage finish. Do not disassemble cartridge unless instructed.

Regulatory Information

This product complies with applicable plumbing standards and regulations. IKEA of Sweden AB. All rights reserved. The IKEA GLYPEN faucet is designed and tested for residential use. For technical support or warranty claims, visit www.ikea.com or contact IKEA customer service at 1-888-888-4532.

Troubleshooting

Reset: For handle issues, try adjusting tension screw. For persistent problems, contact support.

Service: 1-888-888-4532; www.ikea.com