IKEA FYXNÄS 104.640.61 Floor Lamp instructions manual

The IKEA FYXNÄS 104.640.61 is a modern floor lamp featuring a tripod base, adjustable height, and a fabric shade. It requires assembly and uses an E27 bulb (max 13W LED or equivalent, not included). Below are key sections for safety, parts list, assembly instructions, operation, care, and troubleshooting.

Parts & Tools Included

Before assembly, verify all parts are present. Key components: Tripod base legs (3), center pole sections (2), fabric shade, socket assembly, cord with switch, screws, and Allen key.

Safety Instructions

Read all instructions before assembly and use.

1. Use only E27 bulb, max 13W LED or equivalent. Do not exceed wattage.
2. Ensure lamp is on a stable, level surface to prevent tipping.
3. Unplug lamp before assembly, cleaning, or bulb replacement.
4. Keep away from heat sources and moisture.
5. Do not use if cord or plug is damaged.

WARNING! Risk of electric shock. Ensure power is off during assembly. Do not modify cord or socket.

Assembly Steps

Estimated assembly time: 15-20 minutes. Work on a soft surface to avoid scratches.

1. Attach legs: Insert each tripod leg (A) into base slots on lower pole (B). Secure with provided screws (F) using Allen key (H). Tighten firmly.
2. Connect poles: Screw upper pole section (C) into lower pole (B). Ensure tight fit.
3. Install socket: Thread cord through center of poles. Attach socket assembly (E) to top of upper pole. Secure with included ring.
4. Attach shade: Place fabric shade (D) over socket. Secure with shade attachment ring (G). Ensure shade is straight.
5. Final check: Ensure all screws are tight and lamp stands steadily. Plug in cord.

CAUTION! Do not overtighten screws. Handle fabric shade carefully to avoid tearing.

Specifications

• Model: FYXNÄS 104.640.61
• Type: Floor lamp with tripod base
• Height: Adjustable, approx. 140-160 cm
• Base Diameter: Approx. 50 cm
• Shade Material: Polyester fabric
• Frame Material: Steel, powder-coated
• Bulb Socket: E27
• Max Wattage: 13W LED or equivalent (bulb not included)
• Cord Length: 180 cm
• Switch Type: In-line cord switch
• Voltage: 110-240V, 50/60Hz

Lamp Operation

Once assembled and bulb installed:

1. Plug cord into wall outlet.
2. Use in-line switch on cord to turn lamp ON/OFF.
3. Adjust lamp position by gently moving tripod legs. Ensure all legs remain on floor.
4. For optimal light, place lamp near seating or reading area.

Tip: Use with a dimmable LED bulb for adjustable brightness (if compatible).

Bulb Replacement

To replace bulb:

1. Unplug lamp and allow bulb to cool completely.
2. Gently press fabric shade upward to access bulb.
3. Unscrew old bulb counterclockwise.
4. Screw new E27 bulb (max 13W LED) clockwise until snug. Do not overtighten.
5. Reposition shade and plug in lamp.

WARNING! Use only recommended bulb type. Higher wattage may cause overheating.

Care & Maintenance

Unplug before cleaning.

• Fabric shade: Use soft brush or vacuum with brush attachment. Do not wash.
• Metal parts: Wipe with dry, soft cloth. For stains, use damp cloth with mild soap. Dry immediately.
• Cord: Keep away from sharp edges and heat. Do not pinch or knot.

CAUTION! Do not immerse in water or use abrasive cleaners.

Troubleshooting

Warranty & Support

This IKEA product is covered by warranty according to local IKEA policies. Retain receipt as proof of purchase.

For missing parts, assembly help, or product support:

• Visit: www.ikea.com
• Contact your local IKEA store
• Refer to product number: 104.640.61

Recycling: Dispose of packaging and product responsibly according to local regulations.