IKEA FRIHULT 104.316.07 Ceiling Lamp instructions manual

The IKEA FRIHULT 104.316.07 is a ceiling lamp designed for indoor use, featuring a minimalist design suitable for various room settings. It requires assembly and installation, which should be performed by a qualified electrician to ensure safety. Below are key sections covering safety, parts included, assembly, installation, operation, care, and troubleshooting.

1. Safety Information 2. Parts Included 3. Tools Required 4. Assembly Instructions 5. Installation 6. Operation 7. Bulb Replacement 8. Care & Maintenance 9. Specifications 10. Troubleshooting 11. Warranty & Support

Safety Information

Before installation, read all safety instructions carefully.

Warning	Description
Electrical Safety	Installation must be performed by a qualified electrician. Ensure power is turned off at the circuit breaker before beginning.
Weight Limit	Do not exceed the maximum weight limit specified for the ceiling mount.
Bulb Type	Use only LED bulbs with the specified wattage and base type (E27). Do not use higher wattage bulbs than recommended.
Location	For indoor use only. Do not install in damp or wet locations (e.g., bathrooms) unless rated for such use.
Children	Keep packaging materials away from children to avoid suffocation risk.

Parts Included

Check that all parts are present before starting assembly.

Ceiling lamp shade (FRIHULT) - 1 piece.
Mounting bracket - 1 piece.
Wire connectors (plastic caps) - 3 pieces.
Screws and wall plugs - set.
Instruction manual - 1 copy.

NOTE: Light bulb(s) are not included. Purchase separately.

Tools Required

You will need the following tools for installation:

Screwdriver (Phillips head).
Drill (if mounting to concrete ceiling).
Wire stripper/cutter.
Ladder or step stool.
Voltage tester.

CAUTION! Use appropriate personal protective equipment (PPE) such as safety glasses.

Assembly Instructions

Follow these steps to assemble the lamp before installation.

Remove all parts from packaging and lay them on a clean, flat surface.
Attach the mounting bracket to the ceiling lamp base using the provided screws. Do not fully tighten yet.
Insert the bulb holder into the lamp shade opening and secure it according to the diagram.
Ensure all connections are snug but do not over-tighten to avoid damaging parts.

Tip: Refer to the included pictorial diagram for visual guidance.

Installation

WARNING! Turn off electricity at the main circuit breaker before proceeding.

Mark the ceiling where the lamp will be installed, ensuring it is away from joists or obstructions.
If necessary, drill holes and insert wall plugs for the mounting bracket.
Secure the mounting bracket to the ceiling using screws.
Connect the lamp wires to the household wiring: black/red to live, white/blue to neutral, green/yellow to ground. Use wire connectors.
Attach the assembled lamp to the mounting bracket and secure with final screws.
Install the appropriate LED bulb (not included).
Restore power and test the lamp.

Operation

Operate the lamp using the existing wall switch connected to the circuit.

Turn the wall switch ON to illuminate the lamp.
Turn the wall switch OFF to turn off the lamp.
The lamp is designed for standard indoor lighting use.

Note: If using with a dimmer switch, ensure both the dimmer and the LED bulb are dimmable compatible.

Bulb Replacement

Turn off the power at the wall switch and allow the bulb to cool if it was recently on.
Gently twist the bulb counterclockwise to remove it from the socket.
Insert a new LED bulb with an E27 base, matching the recommended wattage (max 13W LED or equivalent).
Twist clockwise until snug. Do not overtighten.
Restore power and test.

WARNING! Never touch the bulb with bare hands when hot. Use a cloth if necessary.

Care & Maintenance

To clean, first turn off power and let the lamp cool.

Use a dry, soft cloth to dust the lamp shade and base.
For stubborn marks, use a slightly damp cloth. Do not use abrasive cleaners or chemicals.
Never immerse the lamp or any electrical parts in water.

CAUTION! Do not clean while the lamp is connected to power or is hot.

Specifications

Model: FRIHULT 104.316.07
Type: Ceiling Lamp
Material: Steel/Plastic (Finish: White)
Dimensions: Diameter 35 cm, Height 15 cm
Bulb Socket: E27
Max Wattage: 13W LED (equivalent to 100W incandescent)
Voltage: 220-240V AC, 50/60Hz
Weight: 1.2 kg
IP Rating: IP20 (Not suitable for wet locations)

Troubleshooting

Symptom	Possible Cause	Corrective Action
Lamp does not turn on	Power off / Bulb faulty / Loose connection	Check circuit breaker and wall switch. Replace bulb. Ensure wires are securely connected.
Lamp flickers	Loose bulb / Incompatible dimmer / Faulty bulb	Tighten bulb. Ensure dimmer and bulb are dimmable compatible. Try a different bulb.
Lamp gets hot	Bulb wattage too high / Poor ventilation	Use only recommended LED bulb. Ensure lamp is not covered or in an enclosed fixture.
Unusual noise	Loose parts / Electrical hum from dimmer	Tighten all screws and the bulb. If using a dimmer, the hum may be normal for some types.
Light output is dim	Old bulb / Low voltage / Too many lamps on circuit	Replace bulb. Check household voltage. Reduce load on the electrical circuit.

Warranty & Support

This IKEA product is covered by a limited warranty. Refer to the IKEA warranty terms included in the packaging or available at IKEA stores.

For support:
Visit: www.ikea.com
Contact your local IKEA store.
Have the model number (104.316.07) and receipt ready when requesting service.

Disposal: Dispose of the product and any electronic components according to local regulations. Do not dispose of with household waste.