IKEA FLOTTILJ 805.523.18 Desk Lamp instructions manual

The IKEA FLOTTILJ 805.523.18 is a modern desk lamp featuring an adjustable arm and head for targeted lighting, an energy-efficient LED light source, touch-sensitive on/off/dimming control, and a stable weighted base. It is designed for home office, study, or bedside use. Below are key sections for safety, assembly, operation, care, and troubleshooting.

Features at a Glance

Key components: Adjustable metal arm, Rotatable lamp head, Touch-sensitive control base, Non-slip weighted foot, Integrated LED module.

Parts & Tools Required

Inspect all parts from packaging before assembly.

1. Lamp base (with integrated touch control and weighted foot)
2. Adjustable arm (gooseneck)
3. Lamp head (with integrated LED)
4. Power cable (attached to base)
5. Instruction manual (this document)

Note: No tools required for assembly. All parts connect via screw threads or push-fit connections.

Assembly Instructions

Follow these steps to assemble your FLOTTILJ desk lamp.

1. Place the weighted base on a flat, stable surface.
2. Take the adjustable arm and screw it clockwise into the threaded socket on the top of the base. Hand-tighten firmly.
3. Take the lamp head and align its connector with the end of the adjustable arm. Push and twist clockwise until it locks into place.
4. Ensure all connections are secure but do not over-tighten.
5. Plug the power cable into a standard wall outlet (120V AC, 60Hz).

WARNING! Do not plug in the lamp until assembly is complete. Ensure the power outlet is easily accessible.

Specifications

• Model: FLOTTILJ 805.523.18
• Light Source: Integrated non-replaceable LED
• Luminous Flux: 300 lumens
• Color Temperature: 2700K (Warm White)
• Power Consumption: 5W
• Input Voltage: 120V AC, 60Hz
• Dimmable: Yes, via touch control (3 levels + Off)
• Adjustability: Arm fully flexible; head 360° rotatable
• Base: Weighted, non-slip, diameter 15 cm
• Cable: 1.5 m, fixed
• Operating Temperature: 0°C to 40°C (32°F to 104°F)

Controls and Operation

The lamp is controlled via a touch-sensitive area on the top of the base.

Operation:

1. To turn On: Briefly touch the control area. The lamp will turn on at the last used brightness level.
2. To change brightness: While the lamp is on, touch and hold the control area. The brightness will cycle through three levels (Low, Medium, High). Release to select.
3. To turn Off: Briefly touch the control area when the lamp is on. It will turn off immediately.

Note: The touch control is designed for dry fingers. It may not respond if the surface is wet or if you are wearing thick gloves.

Positioning & Adjustment

For optimal lighting, adjust the arm and head.

1. Gently bend the gooseneck arm to position the light where needed.
2. Rotate the lamp head to direct the light beam onto your work surface.
3. Ensure the weighted base remains flat and stable during adjustment.
4. Avoid bending the arm at extreme angles repeatedly, as this may reduce its longevity.

Tip: Position the lamp so the light comes from the side opposite your writing hand to minimize shadows.

Light Source Information

This lamp uses an integrated, non-replaceable LED module.

• Life expectancy: Approx. 25,000 hours under normal use.
• Non-replaceable: The LED is built into the lamp head. If the light fails, the entire lamp unit must be replaced.
• Energy efficiency: Consumes very little power compared to traditional incandescent bulbs.
• No UV/IR: The LED emits minimal heat and no ultraviolet or infrared radiation.

WARNING! Do not attempt to open or disassemble the lamp head. There are no user-serviceable parts inside.

Safety Information

Read all safety instructions before use.

• Use only with 120V AC, 60Hz power outlets.
• Do not use outdoors or in damp/wet locations.
• Do not place the lamp near heat sources (radiators, stoves).
• This lamp is not a toy. Keep away from children under 3 years old.
• Do not cover the lamp or place objects on it during operation.
• If the power cord is damaged, it must be replaced by the manufacturer or a qualified service agent.
• Unplug the lamp before cleaning or when not in use for extended periods.

Care & Cleaning

Unplug the lamp from the wall outlet before cleaning.

1. Use a soft, dry cloth to wipe the base, arm, and head.
2. For stubborn marks, dampen the cloth slightly with water. Do not use cleaning sprays or solvents.
3. Ensure no moisture enters the joints or the touch control area.
4. Never immerse any part of the lamp in water or other liquids.

CAUTION! Do not use abrasive cleaners, scouring pads, or chemicals, as they may damage the surface.

Warranty & Support

IKEA limited warranty applies. Refer to the IKEA warranty document included with your purchase or available at IKEA stores.

Support: For product assistance, assembly help, or warranty claims:

• Visit: www.ikea.com
• Contact your local IKEA store.
• Refer to the contact information on your original receipt.

This product complies with applicable safety standards. Copyright and design rights belong to Inter IKEA Systems B.V.

Troubleshooting

Disposal: At end of life, do not dispose with household waste. Recycle according to local regulations for electronic equipment.

Service: This product contains no user-serviceable parts. Do not attempt to repair it yourself.