IKEA FINNALA 095.051.66 1 Seat Armchair Cover instructions manual

The IKEA FINNALA 095.051.66 is a replacement cover designed specifically for the FINNALA 1-seat armchair. This manual provides essential information for safely removing the old cover and installing the new one, ensuring a proper fit and maintaining the chair's appearance. Below are key sections covering safety, parts identification, step-by-step installation, care instructions, and warranty information.

1. Parts & Tools Checklist 2. Safety Information 3. Removing the Old Cover 4. Installing the New Cover 5. Adjusting for a Perfect Fit 6. Care & Maintenance 7. Troubleshooting 8. Specifications & Compatibility 9. Warranty & Support

Parts & Tools Checklist

Before you begin, verify you have all necessary parts. No special tools are required.

Part Name	Quantity	Description
FINNALA Cover (Main Body)	1	Pre-shaped fabric cover for the seat, back, and arms.
Zipper Pull Tabs	2	Attached to zippers for seat cushion and back cushion covers.
Instruction Manual	1	This document.

Note: The cover is designed for model FINNALA armchair only. Ensure your chair frame is clean and undamaged.

Safety Information

Always prioritize safety during installation.

Work Area: Choose a clean, spacious, and well-lit floor area.
Lifting: The armchair frame is heavy. Lift with your legs, not your back. Ask for help if needed.
Sharp Objects: Do not use knives or sharp tools near the fabric. Use your hands to adjust and tuck.
Children & Pets: Keep them away from the work area to prevent accidents or interference.

WARNING! Ensure the armchair is stable and on a flat surface before starting. Do not stand on the chair frame.

Removing the Old Cover

Follow these steps to carefully remove the existing cover without damaging the foam cushions or chair frame.

Unzip: Locate the zippers under the seat cushion and behind the back cushion. Fully unzip them.
Remove Cushions: Gently pull the seat cushion out of its cover. Then, carefully remove the back cushion.
Peel Off Cover: Starting from the bottom, peel the main cover off the armchair frame. It may be snug; pull evenly from all sides.
Inspect Frame: Once the cover is off, check the wooden frame and webbing for any damage or loose parts. Tighten if necessary.

Tip: If the old cover is to be reused or recycled, fold it neatly after removal.

Installing the New Cover

Take your time to align the new cover correctly for the best result.

Position Cover: Identify the front/back and top/bottom of the new cover. The zipper flaps should face the inside of the chair.
Drape Over Frame: Drape the cover over the bare armchair frame. Align the armholes and corners first.
Work from Bottom Up: Start by pulling the cover over the base and legs. Then, work it up over the arms and back.
Insert Cushions: Place the foam back cushion into its pocket in the cover. Insert the seat cushion into its cover pouch.
Zip Up: Zip both the seat and back cushion covers completely. Ensure the zipper pull tabs are tucked in to prevent snagging.

CAUTION! Do not force the fabric. If it feels stuck, check for misalignment or twisting.

Adjusting for a Perfect Fit

After installation, smooth out wrinkles and ensure a taut fit.

Smoothing: Use your hands to smooth the fabric from the center outward, removing large wrinkles.
Tucking: Tuck any excess fabric neatly into the crevices between the cushions and the frame.
Final Check: Sit in the chair gently. The cover may settle. Re-smooth and adjust as needed after the first few uses.

Note: Some creases are normal initially and will relax over time.

Care & Maintenance

Proper care extends the life of your cover.

Regular Care: Vacuum regularly with an upholstery attachment to remove dust and crumbs.

Spot Cleaning: Blot spills immediately with a clean, absorbent cloth. Use a mild soap solution and a soft brush for stains. Always test on an inconspicuous area first.

Washing: Check the care label. Most FINNALA covers are removable and machine washable at 40°C on a gentle cycle. Do not bleach. Tumble dry on low heat or air dry.

CAUTION! Do not iron. Do not dry clean unless the label explicitly states it is safe.

Troubleshooting

Issue	Possible Cause	Solution
Cover seems too tight	Not fully aligned; fabric twisted.	Remove and re-drape, ensuring all seams align with chair corners.
Zipper won't close	Fabric caught in zipper; misalignment.	Open zipper fully, clear any trapped fabric, and realign the teeth before closing.
Wrinkles won't smooth out	Cover needs to settle; installed too loosely.	Use the chair for a few days. If persistent, unzip, tighten the cover on the frame, and re-zip.
Cushions feel lumpy inside cover	Cushion not inserted properly.	Remove cushion, fluff it, and re-insert, ensuring it fills all corners of the cover pocket.

Specifications & Compatibility

Product Name: FINNALA Cover for 1-seat armchair.
Article Number: 095.051.66
Compatible With: IKEA FINNALA 1-seat armchair frame only.
Material: Polyester/Elastane blend (Check label for specific composition).
Color/Fabric: As specified on product packaging.
Care: Machine washable (see Care label).

Warranty & Support

This cover is covered by IKEA's limited warranty. Refer to the IKEA warranty document for full terms.

Need Help? For assembly support or missing parts:

Visit the IKEA store where you made your purchase.
Contact IKEA Customer Support: Visit www.ikea.com for your local contact number.
Have your article number (095.051.66) and receipt ready.

Recycling: At end of life, please recycle or dispose of the fabric cover according to local regulations.