IKEA ENSEN 594.408.94 Faucet instructions manual

The IKEA ENSEN 594.408.94 is a single-lever kitchen faucet designed for durability and ease of use. It features a pull-down spray head, ceramic disc cartridge for smooth operation and drip-free performance, 360-degree swivel spout, and a brushed nickel finish. The faucet is designed for standard 3-hole sink installation (center hole spacing 4-1/4" to 8") and includes all necessary mounting hardware. Below are key sections for safety, features, installation, operation, maintenance, and troubleshooting.

1. Features at a Glance 2. Installation 3. First-Time Setup 4. Specifications 5. Controls and Operation 6. Connecting to Water Supply 7. Using the Pull-Down Spray Head 8. Care & Cleaning 9. Regulatory Information 10. Troubleshooting

Features at a Glance

Key components: Single-lever handle, pull-down spray head with hose, ceramic disc cartridge, 360-degree swivel spout, mounting hardware, and water supply hoses.

Feature	Description
Single-lever handle	Controls water temperature and flow with one hand
Ceramic disc cartridge	Ensures smooth operation and prevents leaks
Pull-down spray head	Extends for flexible rinsing; retracts automatically
360-degree swivel spout	Provides full sink coverage
Brushed nickel finish	Resistant to corrosion and fingerprints
Included mounting hardware	For secure installation on 3-hole sinks
Water supply hoses	Flexible connectors for hot and cold water lines
Aerator	Reduces splashing and conserves water
Quick-connect system	Simplifies spray head hose connection
Weighted hose	Ensures spray head retracts properly

Installation

Unpack and inspect all parts. Ensure sink is clean and dry before installation.

Prepare sink: Remove old faucet and clean mounting area.
Mount faucet: Insert faucet through sink holes; secure from below with mounting nuts.
Connect spray head hose: Attach quick-connect coupling to faucet body.
Connect water supply: Attach flexible hoses to hot and cold water valves.
Secure connections: Tighten all nuts and fittings; avoid over-tightening.

WARNING! Turn off water supply before installation. Use two wrenches to avoid damaging fittings.

First-Time Setup

After installation, test faucet operation.

Turn on water supply: Slowly open hot and cold water valves.
Check for leaks: Inspect all connections for drips.
Operate handle: Move lever to test hot and cold water flow.
Test spray head: Pull down and release to ensure proper retraction.
Adjust spray mode: Rotate spray head ring to switch between stream and spray.

CAUTION! Test for leaks before regular use. If leaks persist, tighten connections or contact support.

Specifications

Model: ENSEN 594.408.94
Type: Single-lever kitchen faucet with pull-down spray
Finish: Brushed nickel
Spout Height: 9.8 inches (250 mm)
Spout Reach: 9.4 inches (240 mm)
Hose Length: 59 inches (1500 mm)
Installation: 3-hole sink (center hole spacing 4-1/4" to 8")
Cartridge: Ceramic disc
Flow Rate: 1.8 GPM (6.8 L/min) at 60 psi
Water Pressure: 20-80 psi (1.4-5.5 bar)
Warranty: Limited 5-year warranty

Controls and Operation

Handle controls both temperature and flow rate.

Handle Operation: Left for hot, right for cold; lift to increase flow, lower to decrease.

Spray Head: Pull down to extend; release to retract. Rotate spray head ring to switch between aerated stream (for filling) and spray (for rinsing).

Temperature Memory: Handle can be positioned for preferred temperature setting.

Connecting to Water Supply

Use included flexible hoses for connection.

Ensure water supply is turned off at shut-off valves.
Connect hoses: Attach to faucet tailpieces and water supply valves.
Hand-tighten connections, then use wrench for final quarter-turn.
Turn on water supply slowly and check for leaks.

Tip: Use thread seal tape on connections if needed. Do not overtighten.

Using the Pull-Down Spray Head

The spray head provides flexible cleaning options.

To extend: Pull spray head down from faucet spout.
To retract: Release gently; weighted hose will retract automatically.
Switch modes: Rotate ring at front of spray head to select stream or spray.
For difficult retraction: Ensure hose is not kinked; check weight is properly attached.

WARNING! Do not pull spray head with excessive force. Avoid sharp bends in hose.

Care & Cleaning

Clean regularly with mild soap and water; dry with soft cloth.

DO: Use non-abrasive cleaners. Wipe spills promptly.

DON'T: Use abrasive pads, harsh chemicals, or vinegar-based cleaners.

CAUTION! Avoid cleaners containing ammonia, bleach, or acids. Do not use scouring pads.

Regulatory Information

Complies with ASME A112.18.1/CSA B125.1 plumbing standards. Meets low-lead requirements (NSF/ANSI 372). For warranty claims or support, contact IKEA customer service or visit www.ikea.com.

Troubleshooting

Symptom	Possible Cause	Corrective Action
Leaking from handle	Worn cartridge	Replace ceramic disc cartridge.
Spray head doesn't retract	Kinked hose or missing weight	Straighten hose; ensure weight is attached.
Low water pressure	Clogged aerator	Clean or replace aerator.
Handle is stiff	Mineral buildup	Clean cartridge; if persists, replace.
Water temperature fluctuates	Supply valve issues	Check hot and cold water supply pressures.
Spray pattern uneven	Clogged spray head	Soak spray head in vinegar solution; rinse thoroughly.

Reset: For handle issues, remove and reinstall cartridge.

Service: For warranty service, contact IKEA customer service with proof of purchase.