IKEA ENHET 994.409.10 Leg instructions manual

The IKEA ENHET 994.409.10 Leg is a component designed for use with ENHET kitchen and storage units. These adjustable legs provide stable support, allow for height leveling on uneven floors, and feature a sleek, durable design. Below are key sections for safety, parts identification, assembly, installation, adjustment, care, and troubleshooting.

1. Parts Included 2. Tools Required 3. Safety Instructions 4. Assembly Steps 5. Installation to Cabinet 6. Height Adjustment 7. Weight Capacity & Specifications 8. Care & Maintenance 9. Troubleshooting 10. Warranty & Support

Parts Included

Package contents for ENHET 994.409.10 Leg set.

Part NameQuantityDescription
Adjustable Leg4Main leg body with threaded adjustment mechanism
Mounting Plate4Metal plate for attaching leg to cabinet bottom
Mounting Screws16Screws for securing plate to cabinet (4 per leg)
Plastic Foot Cap4Protective cap for leg base
Instruction Manual1This document

Tools Required

Tools you need to provide for assembly.

  1. Phillips screwdriver (size #2 recommended).
  2. Power drill (optional, for easier screw driving).
  3. Measuring tape.
  4. Pencil for marking.
  5. Level (for final adjustment).

NOTE: Using the correct tool size prevents damage to screw heads.

Safety Instructions

Important safety information to prevent injury and damage.

  1. Work Area: Assemble on a clean, flat, stable surface.
  2. Lifting: Cabinets can be heavy. Use proper lifting technique or get assistance.
  3. Secure Cabinet: Ensure cabinet is stable and cannot tip during leg attachment.
  4. Tool Safety: Use tools as intended. Keep fingers clear of screwdriver tips.
  5. Final Check: Verify all screws are tight and legs are securely attached before loading cabinet.

WARNING! Failure to properly secure legs may result in cabinet instability, tipping, or collapse, causing injury or property damage.

Assembly Steps

Prepare the leg components before attaching to the cabinet.

  1. Inspect Parts: Lay out all parts from the package. Ensure nothing is missing or damaged.
  2. Attach Foot Cap: Press the plastic foot cap onto the base of each leg until it clicks into place.
  3. Prepare Mounting Plate: The mounting plate comes pre-assembled to the leg. Verify the connection is firm.
  4. Extend Leg (Optional): Rotate the leg body counter-clockwise to extend it slightly for easier initial installation.

Tip: Do not fully extend the leg before mounting; leave room for final adjustment.

Installation to Cabinet

Attaching the legs to the ENHET cabinet bottom.

  1. Position Cabinet: Turn the cabinet upside down on a soft, protected surface (e.g., blanket or cardboard).
  2. Mark Positions: Measure and mark the positions for the four legs. They should be placed near each corner, inside the cabinet's frame for optimal support.
  3. Align Plate: Place a leg's mounting plate against the cabinet bottom at a marked position. Ensure it is square to the cabinet edge.
  4. Secure Screws: Using the provided screws, drive one screw into the center hole first to hold the plate. Then, drive in the remaining three screws firmly. Do not overtighten.
  5. Repeat: Attach the remaining three legs in the same manner.
  6. Return Cabinet Upright: Carefully turn the cabinet right-side up with assistance.

CAUTION! The cabinet bottom material may be particleboard. Avoid stripping the screws by applying steady, firm pressure.

Height Adjustment

Leveling the cabinet on an uneven floor.

  1. Place Cabinet: Move the cabinet to its final location.
  2. Check Level: Place a level on top of the cabinet, both front-to-back and side-to-side.
  3. Adjust Legs: To raise the cabinet, rotate the leg body counter-clockwise. To lower, rotate clockwise. Adjust one leg at a time.
  4. Re-check: After each adjustment, check the level again. Repeat until the cabinet is perfectly level and stable (no rocking).
  5. Final Stability: Gently try to rock the cabinet. If it rocks, identify the high corner and slightly lower that leg, or raise the opposite legs until stable.

Note: The adjustment range is typically between 4" and 5.5" (approx. 10-14 cm) from floor to cabinet bottom.

Weight Capacity & Specifications

Care & Maintenance

To ensure longevity and performance.

  1. Cleaning: Wipe legs with a damp cloth. Do not use abrasive cleaners or solvents.
  2. Periodic Check: Every 6-12 months, check that all mounting screws are tight and the cabinet remains level.
  3. Moving Cabinet: If moving the cabinet, retract the legs (rotate clockwise) to avoid bending the adjustment threads.
  4. Floor Protection: The plastic foot caps protect most floors. For very soft floors (vinyl, some laminates), consider an additional protective pad.

CAUTION! Do not exceed the maximum weight capacity. Overloading can cause permanent damage to the legs or cabinet.

Troubleshooting

SymptomPossible CauseCorrective Action
Cabinet wobblesLegs not adjusted properly; uneven floorRe-adjust legs using level. Ensure all four legs contact the floor firmly.
Leg will not turnThreads cross-threaded or dirty; leg under full loadLift cabinet slightly to relieve weight, then try to adjust. Ensure threads are clean.
Screw spins but won't tightenStripped screw hole in cabinetRemove screw. Use a slightly longer or wider screw, or use a wall plug/anchoring compound in the hole.
Leg feels loose at plateMounting plate screws looseTighten all four screws securing the mounting plate to the cabinet.
Plastic foot cap falls offNot fully seated; damagedPress cap firmly onto leg base until an audible click. If damaged, contact IKEA for replacement.

Replacement Parts: For missing or damaged parts, visit your local IKEA store or contact IKEA Customer Service with the article number (994.409.10).

Warranty & Support

IKEA limited warranty applies. See IKEA terms and conditions for details.

IKEA Customer Support:
Website: www.ikea.com
Phone: 1-888-888-4532 (IKEA-USA)
Store Locator: Available on website.

Important: Retain your receipt as proof of purchase for warranty claims.

IKEA ENHET 994.409.10 Leg instructions manual © - All Rights Reserved 2025