IKEA ENHET 094.802.41 Base Sink instructions manual

The IKEA ENHET 094.802.41 is a base sink cabinet designed for the ENHET kitchen series, providing a sturdy and stylish foundation for your sink. It features a white, moisture-resistant finish, adjustable legs for leveling, and is designed to accommodate standard sink bowls. Below are key sections for safety, assembly, installation, use, care, and troubleshooting.

1. Product Overview 2. Included Parts 3. Safety Instructions 4. Assembly Instructions 5. Installation Guide 6. Adjustments & Leveling 7. Care & Maintenance 8. Technical Specifications 9. Warranty Information 10. Troubleshooting

Product Overview

The ENHET base sink cabinet provides a clean, modern look and functional storage space beneath your kitchen sink. It is part of a modular system that allows for flexible kitchen planning.

Feature	Description
Material	Particleboard, foil, ABS plastic
Finish	White, moisture-resistant
Dimensions (WxDxH)	80 x 58 x 80 cm (31 1/2 x 22 7/8 x 31 1/2 ")
Adjustable Legs	4 legs, adjustable for uneven floors
Weight Capacity	Max. load 50 kg (110 lbs) distributed evenly
Compatibility	Designed for ENHET sink bowls and faucets
Pre-drilled Holes	For easy assembly and pipe access
Door	Not included (sold separately)

Included Parts

Check that all parts are included before starting assembly. Contact IKEA if any parts are missing.

Base cabinet frame (1 piece)
Adjustable legs (4 pieces)
Leg screws (8 pieces)
Cam locks and dowels (pre-installed)
Assembly instructions (this manual)

NOTE! Tools required but not included: Phillips screwdriver, hammer, level, measuring tape.

Safety Instructions

Read all instructions before assembly and installation.

Lifting: The cabinet is heavy. Use two people to lift and move it to avoid injury.
Stability: Ensure the cabinet is level and all legs are firmly adjusted and in contact with the floor.
Load: Do not exceed the maximum load capacity. Distribute weight evenly.
Water Exposure: While moisture-resistant, avoid prolonged direct water exposure. Wipe spills immediately.
Children: Do not let children climb or play on the cabinet.

WARNING! An unlevel or unstable cabinet can tip over, causing injury or damage.

Assembly Instructions

Assemble the cabinet on a soft, clean surface to avoid scratches.

Attach Legs: Turn the cabinet frame upside down. Screw the four adjustable legs into the pre-drilled holes at each corner using the provided screws. Hand-tighten first, then secure with a screwdriver.
Flip Cabinet: Carefully turn the cabinet right-side up with the help of another person.
Check Structure: Ensure all joints are secure. Tighten any loose cam locks by turning them clockwise with a screwdriver.

Tip: Do not fully tighten the leg screws until after leveling during installation.

Installation Guide

Install the base cabinet in its final location before placing the sink bowl.

Position: Move the assembled cabinet to its desired location under the countertop.
Level: Use a spirit level on the top of the cabinet. Adjust each leg by turning to raise or lower until the cabinet is perfectly level in all directions.
Secure Legs: Once level, fully tighten the locking nuts on the legs against the cabinet bottom to prevent shifting.
Install Sink: Follow the separate instructions for your ENHET sink bowl to secure it onto the cabinet top.
Connect Plumbing: A professional is recommended for connecting water supply and drain pipes through the pre-cut holes in the cabinet back panel.

CAUTION! Ensure the cabinet is not resting on plumbing lines or electrical cables.

Adjustments & Leveling

Re-level the cabinet if the floor settles or if you move it.

Loosen the locking nut on the leg that needs adjustment.
Turn the leg itself to extend or retract it.
Check with a level and re-tighten the locking nut.
Repeat for all legs as necessary.

Note: The cabinet doors (sold separately) may need adjustment after installation to ensure they hang straight and close properly.

Care & Maintenance

Proper care will extend the life of your cabinet.

Cleaning: Wipe surfaces with a soft, damp cloth. Use a mild, non-abrasive detergent if needed. Dry immediately with a clean cloth.
Avoid: Do not use abrasive cleaners, scouring pads, or harsh chemicals (acetone, bleach).
Moisture: Prevent standing water inside the cabinet. Dry any condensation or leaks promptly.
Inspection: Periodically check leg adjustments and tighten any loose screws or cam locks.

WARNING! Never use a steam cleaner on the cabinet.

Technical Specifications

Article Number: 094.802.41
Product Name: ENHET Base cabinet with drawer/door for sink
Width: 80 cm
Depth: 58 cm
Height: 80 cm (without countertop)
Max Static Load: 50 kg
Package Weight: Approximately 25 kg
Country of Origin: To be specified per region

Warranty Information

This IKEA product is covered by the IKEA commercial warranty. Refer to the IKEA warranty terms in your local store or at IKEA.com for specific duration and conditions. The warranty covers material and manufacturing defects under normal household use.

For Service: Keep your receipt as proof of purchase. Contact your local IKEA store or visit IKEA.com for warranty claims or spare parts.

Troubleshooting

Symptom	Possible Cause	Corrective Action
Cabinet wobbles	Uneven floor or legs not adjusted	Re-level the cabinet by adjusting the legs. Ensure all locking nuts are tight.
Door doesn't close properly (if attached)	Cabinet not level or hinges misaligned	Re-level the cabinet. Adjust the door hinges according to the door's instruction manual.
Water stains or swelling	Prolonged water exposure	Dry area thoroughly. If swelling is severe, the panel may need replacement. Prevent future leaks.
Squeaking noises	Loose joints or legs	Check and tighten all cam locks and leg screws.
Difficulty attaching legs	Threads misaligned	Do not force. Unscrew and start again, ensuring the leg is straight when threading.

Spare Parts: For missing or damaged parts, contact IKEA customer service with the article number (094.802.41).

Support: Visit www.IKEA.com or your local IKEA store for further assistance.