IKEA ENHET 094.771.11 Door instructions manual

The IKEA ENHET 094.771.11 is a door designed for the ENHET modular kitchen and bathroom system. This manual provides essential information for safe and proper assembly, installation, adjustment, and maintenance of the door. Below are key sections covering safety, parts identification, step-by-step assembly, installation, adjustment, care, and troubleshooting.

Parts and Tools

Ensure all parts are present before starting assembly.

Required Tools (not included): Phillips screwdriver (size #2), measuring tape, pencil, level.

Safety Instructions

WARNING! To prevent injury and damage, read all instructions before assembly and installation.

1. Work Area: Assemble on a clean, flat, stable surface covered with a soft cloth to prevent scratches.
2. Lifting: The door panel is heavy. Use proper lifting techniques or ask for assistance.
3. Children and Pets: Keep children and pets away from the assembly area. Small parts are a choking hazard.
4. Tool Safety: Use tools as intended. Ensure screwdriver fits screw heads properly to avoid stripping.
5. Cabinet Stability: Ensure the cabinet frame is securely mounted to the wall before installing the door.

CAUTION! Do not force parts during assembly. If something doesn't fit, re-check the instructions.

Assembly Instructions

Follow these steps to attach the hinges to the door panel.

1. Identify Hinge Side: Determine if the door will be left-opening or right-opening. The hinges must be installed on the correct side.
2. Position Hinge on Door:
   • Place the door panel face down on a protected surface.
   • Position the hinge mounting plate on the back of the door according to the pre-drilled holes or template. The hinge should be placed 100mm from the top and bottom edges of the door (standard for ENHET).
3. Attach Hinges:
   • Insert the provided screws through the hinge plate and into the door.
   • Hand-tighten all screws first, then use a screwdriver to secure them firmly. Do not overtighten.
   • Repeat for the second hinge.
4. Attach Cover Caps: Snap the plastic cover caps onto the hinge arms to conceal the screws.

Installation to Cabinet Frame

Mounting the door to the ENHET cabinet frame.

1. Prepare Cabinet: Ensure the cabinet frame is level and securely attached to the wall.
2. Position Door: Hold the door with attached hinges near the cabinet opening. Align the hinge arms with the mounting plates on the cabinet frame (if pre-installed) or with the marked positions.
3. Initial Attachment:
   • Engage the hinge arm into the cabinet mounting plate. You should hear a click when it locks into place.
   • For screw-on plates, align the hinge arm and secure it with the provided screws to the cabinet interior side panel.
4. Check Operation: Gently open and close the door. It should move smoothly. The door may not be perfectly aligned at this stage.

Tip: It is easier to install the door with the help of a second person to hold it in place.

Hinge Adjustment

Use the adjustment screws on the hinges to align the door perfectly. Refer to the hinge for three types of screws:

1. Close Door: Observe the gaps around the door.
2. Make Small Adjustments: Use a screwdriver to turn the adjustment screws. Turn 1/4 to 1/2 turn at a time.
   • To raise the door, turn the height screw clockwise.
   • To move the door outward, turn the depth screw counter-clockwise.
3. Check Alignment: After each adjustment, close the door to check for even gaps (typically 2-3mm) on all sides and that the door sits flush with adjacent doors/drawers.
4. Final Check: Open and close the door several times to ensure smooth operation and that it stays in alignment.

Care and Cleaning

Proper care will maintain the appearance and function of your ENHET door.

• Cleaning: Use a soft, damp cloth with a mild detergent. Wipe dry immediately with a clean, soft cloth.
• Avoid: Abrasive cleaners, scouring pads, harsh chemicals, acetone, or ammonia-based products.
• Hinges: Keep hinges free of grease and debris. Do not lubricate unless specified; most IKEA hinges are self-lubricating.

CAUTION! Never use excessive water. Avoid letting liquids sit on the surface or enter seams.

Technical Specifications

• Product Name: ENHET Door
• Article Number: 094.771.11
• Color/Finish: As specified on packaging (e.g., White, Stain, etc.)
• Material: Particleboard, foil
• Dimensions (H x W x D): Refer to packaging for exact size (e.g., 400mm x 600mm x 18mm).
• Weight: Approximately 3-5 kg (varies by size).
• Compatibility: Designed for ENHET cabinet frames. Requires ENHET hinge system.
• Max Load on Hinge: As per hinge specifications. Do not exceed.

Warranty and Support

This IKEA product is covered by the IKEA limited warranty. For warranty terms, visit www.ikea.com.

Customer Support:
IKEA US: 1-888-888-4532
IKEA Canada: 1-866-866-4532
Website: www.ikea.com

Spare Parts: Hinges, screws, and other small parts are available for purchase at IKEA stores or via customer service.

Troubleshooting

Note: If problems cannot be resolved, contact IKEA customer support for assistance or to order replacement parts.