IKEA ENHET 005.193.18 Base Cabinet instructions manual

The IKEA ENHET 005.193.18 is a base cabinet designed for kitchen, bathroom, or utility room storage. It features a clean, minimalist design, adjustable legs for leveling, and is part of the modular ENHET series for flexible configuration. Below are key sections for safety, parts list, assembly, installation, use, care, and troubleshooting.

1. Parts & Hardware 2. Safety Instructions 3. Assembly Steps 4. Installation & Leveling 5. Specifications 6. Mounting & Securing 7. Use & Configuration 8. Care & Cleaning 9. Warranty Information 10. Troubleshooting

Parts & Hardware

Key components: Cabinet frame, back panel, adjustable legs, mounting brackets, screws, cam locks, dowels.

Part	Description	Quantity
Cabinet frame	Main body with pre-drilled holes	1
Back panel	Fiberboard panel for rear stability	1
Adjustable legs	Plastic legs with screw adjustment	4
Mounting brackets	For wall attachment (if required)	2
Cam locks & dowels	For connecting panels	Set
Screws	Various sizes for assembly	Packet
Instruction manual	This guide	1

Safety Instructions

Read all instructions before assembly. Use proper tools.

Lifting: Cabinet is heavy; lift with care or use two people.
Stability: Ensure cabinet is level and secure to prevent tipping.
Tools: Use recommended screwdriver; avoid power tools on cam locks.
Children: Keep small parts away from children during assembly.

WARNING! Do not stand or sit on cabinet. Ensure it is securely anchored if wall-mounted.

Assembly Steps

Follow numerical order in included pictogram guide.

Prepare workspace: Lay all parts on a clean, soft surface.
Attach legs: Screw adjustable legs into bottom corners.
Connect sides: Use dowels and cam locks to attach side panels to top/bottom panels.
Install back panel: Slide into grooves and secure with provided screws.
Final check: Tighten all cam locks; ensure structure is square.

Tip: Do not fully tighten legs until cabinet is in final position.

Installation & Leveling

Position cabinet: Move to desired location.
Adjust legs: Turn legs to raise/lower each corner; use level on top surface.
Secure to wall (optional): Attach mounting brackets to wall studs; screw cabinet back to brackets.
Final level check: Re-check level after securing.

CAUTION! For safety, wall-mounting is recommended, especially in households with children.

Specifications

Model: ENHET 005.193.18
Type: Base cabinet, frame only
Dimensions (WxHxD): 30" x 30" x 15" (approx.)
Material: Particleboard, foil, plastic
Finish: White, matte
Max Load: 55 lbs (25 kg) distributed evenly on base
Adjustable Leg Height: 4" to 6"
Compatibility: ENHET doors, drawers, and interior organizers sold separately

Mounting & Securing

For added stability, secure cabinet to wall.

Locate wall studs using a stud finder.
Attach mounting brackets to wall at stud locations.
Position cabinet against wall, aligning with brackets.
Screw through cabinet back into brackets.
Check that cabinet does not rock or tilt.

Important: Use appropriate wall anchors if not attaching to studs.

Use & Configuration

Cabinet is designed for base storage. Compatible with ENHET system.

Adding doors/drawers: Purchase ENHET fronts; attach hinges/drawer slides to pre-drilled holes.
Interior organization: Add shelves, dividers, or pull-out trays (sold separately).
Weight distribution: Place heavier items at bottom; do not exceed max load.
Multiple units: Cabinets can be placed side-by-side; use connecting clips for alignment.

Note: Doors and internal fittings are not included with this frame.

Care & Cleaning

Wipe with damp cloth; dry immediately. Do not use abrasive cleaners.

CAUTION! Avoid excessive moisture. Do not use steam cleaners or harsh chemicals.

Warranty Information

IKEA limited warranty applies. See IKEA warranty terms for details. Keep receipt. For service, contact IKEA customer support.

Troubleshooting

Symptom	Possible Cause	Corrective Action
Cabinet wobbles	Legs not adjusted properly	Re-level using adjustable legs; check floor surface.
Doors not aligning	Hinges not installed correctly	Adjust hinge screws; ensure doors are for ENHET system.
Cam lock not tightening	Dowel not fully inserted	Disassemble step; ensure dowel is seated before turning cam lock.
Shelf sagging	Weight limit exceeded	Reduce load; ensure shelf is correctly positioned on supports.
Difficulty attaching back panel	Frame not square	Loosen cam locks; square frame; re-tighten; then insert back panel.

Missing parts? Contact IKEA for replacement parts (005.193.18).

Support: Visit IKEA store or www.ikea.com for assembly help and parts.