IKEA ENHET 005.144.86 Wall Cabinet instructions manual

The IKEA ENHET 005.144.86 is a wall-mounted cabinet designed for kitchen, bathroom, or hallway storage. It features a clean, minimalist design, adjustable shelves, and is part of the ENHET modular system. Below are key sections for safety, parts list, assembly, installation, care, and warranty information.

1. Parts & Hardware Included 2. Tools Required 3. Assembly Instructions 4. Wall Mounting 5. Adjusting Shelves 6. Weight Limits & Safety 7. Care & Cleaning 8. Troubleshooting 9. Warranty & Support

Parts & Hardware Included

Before assembly, verify all parts are present. Contact IKEA if anything is missing.

Part DescriptionQuantityImage Reference
Cabinet frame1A
Back panel1B
Door1C
Adjustable shelves2D
Cam lock screws4E
Wall mounting brackets2F
Shelf support pins8G
Door hinges2H
Door handle1I
Assembly manual1-

Tools Required

You will need the following tools (not included):

WARNING! Use proper tools to avoid injury and ensure secure assembly.

Assembly Instructions

Follow steps in order. Work on a clean, flat surface.

  1. Attach back panel: Place frame face down. Align back panel (B) with pre-drilled holes. Secure with provided screws.
  2. Connect side panels: Insert cam locks into side panels. Align with corresponding holes in top and bottom panels. Turn cam locks 90° clockwise to lock.
  3. Install shelf supports: Insert shelf support pins (G) into desired height positions on inner side panels.
  4. Attach door hinges: Screw hinges (H) to door (C) using provided screws. Then attach hinges to cabinet frame.
  5. Mount handle: Attach door handle (I) to door using screws from inside of door.

CAUTION! Do not overtighten screws; this may damage the material.

Wall Mounting

Cabinet must be securely mounted to wall studs or using appropriate wall anchors.

  1. Locate wall studs using a stud finder. Mark positions.
  2. Hold cabinet against wall at desired height. Use level to ensure it is straight.
  3. Mark drilling points through mounting bracket holes.
  4. Drill pilot holes into studs or wall.
  5. Attach mounting brackets (F) to wall using suitable screws (not always included; verify for your wall type).
  6. Lift cabinet and hook onto mounted brackets. Secure with provided safety screws.

WARNING! Ensure mounting can support cabinet weight when fully loaded. Use two people for lifting.

Adjusting Shelves

Shelves are adjustable to customize storage space.

Tip: Distribute weight evenly across shelves. Do not exceed maximum load per shelf.

Weight Limits & Safety

Care & Cleaning

Use a soft, damp cloth with mild soap. Wipe dry immediately.

Do NOT use: Abrasive cleaners, scouring pads, solvents, or bleach.

CAUTION! Avoid excessive moisture. Do not immerse in water.

Troubleshooting

SymptomPossible CauseCorrective Action
Door does not close properlyHinges misalignedLoosen hinge screws, adjust door position, retighten.
Cabinet feels unstableNot mounted to studs; loose bracketsRemount into wall studs; tighten all screws.
Shelf sags or wobblesOverloaded; pins not fully insertedReduce weight; ensure shelf pins are fully seated in holes.
Scratches on surfaceDuring assembly or useUse touch-up pen (available at IKEA) for minor scratches.
Missing partsPackage incompleteContact IKEA customer service with product number and receipt.

Warranty & Support

IKEA limited warranty applies. See IKEA terms or www.ikea.com for details.

For assembly help: Visit IKEA website for instructional videos.

For missing parts or support: Contact IKEA customer service at 1-888-888-4532 or visit your local IKEA store.

Product Number: 005.144.86

IKEA ENHET 005.144.86 Wall Cabinet instructions manual © - All Rights Reserved 2025