IKEA ENHET 005.144.53 Base Frame instructions manual

The IKEA ENHET 005.144.53 Base Frame is a modular, wall-mounted or freestanding frame designed for kitchen and bathroom storage. It is part of the ENHET series, offering flexibility in configuration with various doors, drawers, and shelves. Constructed from powder-coated steel, it is durable, easy to clean, and designed for simple assembly. Below are key sections for safety, features, parts list, assembly, installation, use, care, and troubleshooting.

Features at a Glance

Key components: Powder-coated steel frame, adjustable feet, pre-drilled holes for mounting and accessories, compatibility with ENHET series doors and interior fittings.

Parts and Hardware

Unpack all parts and check against the list before starting assembly.

1. Main Frame: 1 piece - Powder-coated steel body.
2. Adjustable Feet: 4 pieces - For freestanding installation.
3. Mounting Brackets: 2 pieces - For wall mounting.
4. Screws and Plugs: For wall mounting (type depends on wall material).
5. Assembly Screws: For attaching doors and accessories (may be included with accessories).

WARNING! Keep small parts away from children to avoid choking hazard.

Safety Instructions

Read all instructions before assembly and installation.

1. Wall Mounting: Must be secured to wall studs or solid masonry using appropriate hardware. Do not mount to drywall alone.
2. Freestanding: Ensure adjustable feet are properly tightened and unit is level on floor.
3. Load Capacity: Do not exceed maximum weight limits specified for shelves and frame.
4. Tools: Use correct tools (screwdriver, level, drill, stud finder) to ensure secure installation.
5. Children: Do not allow children to climb on or hang from the unit.

CAUTION! A falling unit can cause serious injury. Ensure it is securely installed.

Assembly Instructions

Assemble the frame before mounting or placing it.

1. Prepare Workspace: Work on a clean, soft surface to avoid scratching the frame.
2. Attach Feet (Freestanding): Screw the four adjustable feet into the pre-drilled holes at the bottom corners of the frame. Hand-tighten, then use a screwdriver to secure.
3. Check Stability: Place frame upright and check that all feet contact the floor. Adjust feet as needed to level the unit.
4. Prepare for Accessories: Identify pre-drilled holes for shelves and doors according to your planned configuration.

Tip: It is easier to attach doors and shelves before mounting the frame to the wall.

Wall Mounting

For a permanent, space-saving installation.

1. Locate Studs: Use a stud finder to locate wall studs. Mark their positions.
2. Position Frame: Hold frame against wall at desired height (use a level). Mark the positions of the mounting bracket holes on the wall.
3. Drill Holes: Drill pilot holes at marked positions, using appropriate drill bit for your wall type (wood stud or masonry). Insert wall plugs if needed.
4. Attach Brackets: Secure the mounting brackets to the wall using provided screws. Ensure they are level and firmly anchored.
5. Hang Frame: Lift the frame and hook it onto the mounted brackets. Ensure it is securely engaged and does not wobble.
6. Final Check: Gently pull on the frame to confirm it is firmly attached to the wall.

WARNING! If you are unsure about wall mounting, consult a professional.

Freestanding Installation

For flexible placement without wall attachment.

1. Attach Feet: Ensure all four adjustable feet are securely screwed into the base of the frame.
2. Choose Location: Place the unit on a firm, level floor. Avoid uneven or soft surfaces.
3. Level the Unit: Adjust the feet by turning them clockwise or counterclockwise until the frame is stable and does not rock.
4. Secure Contents: When adding shelves and storage, distribute weight evenly. Heavier items should be placed on lower shelves.

CAUTION! Do not place on elevated surfaces. The unit is designed for floor placement only.

Adding Doors and Shelves

Customize your storage with ENHET series accessories.

1. Doors: Align hinge holes on the door with corresponding holes on the frame. Insert and tighten screws (usually provided with the door). Adjust hinges if necessary for proper alignment.
2. Shelves: Insert shelf into frame at desired height. Most ENHET shelves simply rest on supports or clip into pre-drilled holes. Ensure shelf is level and secure.
3. Drawers: Follow the specific assembly instructions included with the drawer unit. Typically, runners are attached to the frame first, then the drawer box is inserted.
4. Interior Organizers: Hooks, rods, and other organizers can be attached to the inside of the frame or to shelves using the provided hardware.

Tip: Refer to the individual instruction manual for each accessory for detailed steps.

Care & Maintenance

To keep your ENHET frame looking new.

1. Cleaning: Wipe with a damp cloth and mild detergent. Do not use abrasive cleaners, scouring pads, or solvents.
2. Drying: Wipe dry with a soft cloth to prevent water spots, especially in humid areas like bathrooms.
3. Inspection: Periodically check that wall mounts, screws, and feet are tight. Re-tighten if necessary.
4. Rust Prevention: Although powder-coated, avoid letting water sit on metal surfaces for extended periods.

CAUTION! Do not use steam cleaners or high-pressure washers.

Specifications

• Article Number: 005.144.53
• Series: ENHET
• Type: Base Frame
• Material: Steel, Epoxy/polyester powder coating
• Color: White
• Dimensions (HxWxD): Refer to IKEA product page for exact measurements.
• Weight Capacity (Wall Mounted): Max 55 lbs (25 kg) evenly distributed. (Verify in specific product documentation).
• Weight Capacity (Freestanding): Max 110 lbs (50 kg) evenly distributed. (Verify in specific product documentation).
• Adjustable Foot Range: Approx. 0.4 in (10 mm).
• Warranty: See limited warranty terms.

Warranty Information

IKEA products are covered by a limited warranty. The warranty period and terms vary by country and region. For detailed warranty information, please visit the IKEA website or contact your local IKEA store. Keep your receipt as proof of purchase.

Support: For assembly help, missing parts, or other inquiries, visit www.ikea.com or contact your local IKEA customer service.

Troubleshooting

Note: For missing parts or damaged components, contact IKEA customer service with your article number (005.144.53) and receipt.

Service: www.ikea.com or your local IKEA store.