IKEA EKET 192.864.13 Connection Hardware instructions manual

The IKEA EKET 192.864.13 Connection Hardware is a set of components designed for assembling and connecting EKET storage units. It includes connectors, screws, dowels, and other necessary hardware to securely join cabinets, create wall-mounted configurations, or build freestanding combinations. Below are key sections for safety, components, installation, assembly steps, mounting options, and troubleshooting.

Components Overview

Key components included in the EKET 192.864.13 Connection Hardware pack.

Safety Information

Important safety precautions to follow during assembly and installation.

1. Work on a clean, flat surface to prevent parts from rolling or getting lost.
2. Use proper tools as specified to avoid damaging components.
3. Check wall stability before mounting; use wall anchors for drywall.
4. Do not exceed weight limits specified for each configuration.
5. Keep small parts away from children during assembly.

WARNING! Wall-mounted units must be securely attached to wall studs or appropriate anchors. Failure to do so may result in unit falling and causing injury or damage.

Tools Required

Tools needed for successful assembly.

• Phillips screwdriver (size #2) or cordless drill with Phillips bit
• Hammer (for tapping dowels if needed)
• Level (for ensuring units are straight)
• Measuring tape (for proper placement)
• Pencil (for marking drill holes)
• Stud finder (recommended for wall mounting)

Note: All necessary hardware is included in the package.

Assembly Instructions

Step-by-step guide to assemble EKET units using the connection hardware.

1. Prepare components: Lay out all parts and identify each piece using the component diagram.
2. Insert dowel pins: Gently tap dowels into pre-drilled holes on cabinet sides where connection will occur.
3. Align cabinets: Place cabinets side by side, ensuring dowels align with corresponding holes.
4. Secure with connector screws: Insert screws through connector holes and tighten until snug (do not overtighten).
5. Engage cam locks: Turn cam locks 90 degrees clockwise to lock connectors in place.
6. Attach cover caps: Press cover caps over screw heads for finished appearance.

Tip: Assemble on a soft surface (carpet or blanket) to prevent scratching cabinet finishes.

Wall Mounting Guide

Instructions for securely mounting EKET units to the wall.

1. Locate wall studs: Use stud finder to locate solid wood studs in wall.
2. Mark bracket positions: Hold bracket against wall at desired height, mark screw holes with pencil.
3. Drill pilot holes: Drill holes at marked positions (use appropriate drill bit for your wall type).
4. Install wall anchors: If not drilling into studs, insert appropriate wall anchors for your wall material.
5. Attach brackets: Secure brackets to wall using provided screws, ensuring they are level.
6. Hang cabinet: Lift cabinet onto brackets, ensuring it clicks securely into place.
7. Test stability: Gently pull on cabinet to confirm it is securely mounted.

CAUTION! For plaster or drywall, always use appropriate wall anchors rated for the cabinet's weight.

Connecting Multiple Units

Creating combinations of EKET cabinets for various configurations.

Note: Maximum recommended height for stacked units is 4 cabinets (approximately 60 inches).

Weight Limits & Specifications

• Maximum load per cabinet: 22 lbs (10 kg) distributed evenly
• Maximum stacked load: 66 lbs (30 kg) for 3 stacked units
• Wall bracket capacity: 33 lbs (15 kg) per bracket
• Material: Steel connectors, plastic cam locks, ABS cover caps
• Color: White (matches standard EKET finishes)
• Compatibility: All EKET cabinet sizes and colors

Warning: Exceeding weight limits may cause damage to cabinets or mounting system.

Care & Maintenance

Proper care for your EKET connection hardware and cabinets.

1. Regular inspection: Check connectors and brackets every 6 months for tightness.
2. Cleaning: Wipe with dry cloth only; avoid chemical cleaners on plastic parts.
3. Tightening: If cabinets become loose, tighten connector screws with screwdriver.
4. Relocation: When moving cabinets, disassemble completely rather than dragging connected units.

CAUTION! Do not use lubricants on cam locks or connectors as this may attract dust and cause malfunction.

Regulatory Information

IKEA EKET 192.864.13 Connection Hardware meets international safety standards for furniture hardware. Tested according to EN 14749:2016 for domestic storage furniture. All materials comply with REACH regulations for chemical safety. Copyright © IKEA of Sweden AB. For additional support, visit www.ikea.com or contact your local IKEA customer service.

Troubleshooting

Replacement Parts: Available through IKEA customer service or www.ikea.com.

Warranty: 10-year limited warranty on connection hardware. See IKEA warranty terms for details.