IKEA EKENABBEN 194.368.32 Shelf instructions manual

The IKEA EKENABBEN 194.368.32 is a wall-mounted shelf unit designed for storage and display. It features a clean, modern design with metal brackets and a particleboard shelf coated with melamine foil. Below are key sections for safety, parts list, assembly instructions, mounting, care, and troubleshooting.

1. Parts & Tools Required 2. Safety Information 3. Assembly Instructions 4. Wall Mounting 5. Weight Limits & Specifications 6. Care & Maintenance 7. Troubleshooting 8. Warranty & Support

Parts & Tools Required

Included components and tools needed for assembly.

Part Number	Description	Quantity
10000001	EKENABBEN Shelf board	1
10000002	Metal wall bracket	2
10000003	Screw for bracket to wall	4
10000004	Screw for shelf to bracket	4
10000005	Wall plug (for solid walls)	4
-	Allen key (included)	1

Tools you need: Phillips screwdriver, drill, hammer, level, pencil, measuring tape.

Safety Information

Important warnings and precautions for safe assembly and use.

Wall suitability: Mount only to solid walls (concrete, brick, studs). Do not mount to hollow drywall without proper anchors.
Weight limit: Do not exceed maximum load of 15 kg (33 lbs) evenly distributed.
Child safety: Do not allow children to climb or hang on the shelf.
Assembly: Use two people for handling and mounting to prevent injury.
Check stability: Ensure all screws are tight and shelf is level before use.

WARNING! Improper mounting can cause the shelf to fall, resulting in injury or damage. Follow instructions carefully.

Assembly Instructions

Step-by-step guide to assemble the shelf unit.

Unpack: Remove all parts from packaging and lay on a soft surface to avoid scratches.
Identify parts: Refer to the parts list table to verify all components are present.
Attach brackets to shelf:
- Place the shelf board upside down on a protected surface.
- Position the two metal brackets on the underside of the shelf, aligning with the pre-drilled holes.
- Use the included Allen key to tighten the 4 smaller screws (part 10000004) through the bracket into the shelf. Do not overtighten.
Check alignment: Ensure brackets are parallel and securely attached.

Tip: Keep packaging until assembly is complete in case parts need to be returned.

Wall Mounting

Instructions for securely mounting the assembled shelf to the wall.

Choose location: Select a wall suitable for the load. Use a stud finder if mounting to wooden studs.
Mark bracket positions:
- Hold the shelf assembly against the wall at the desired height.
- Use a level to ensure it is perfectly horizontal.
- Mark the wall through the screw holes on each bracket with a pencil.
Drill holes: Drill holes at the marked points using a drill bit appropriate for your wall type and the included wall plugs.
Insert wall plugs: Tap the plastic wall plugs (10000005) into the drilled holes until flush with the wall surface.
Mount shelf:
- Align the brackets with the holes.
- Insert the 4 larger screws (10000003) through the brackets and into the wall plugs.
- Tighten securely with a screwdriver.
Final check: Gently pull down on the shelf to test stability. Ensure it does not wobble.

CAUTION! If drilling into tiles, use a special tile drill bit to prevent cracking. If unsure about wall type, consult a professional.

Weight Limits & Specifications

Model: EKENABBEN 194.368.32
Color: White
Dimensions (LxWxH): 80 cm x 20 cm x 4 cm (31.5" x 7.9" x 1.6")
Shelf Material: Particleboard, Melamine foil
Bracket Material: Steel, Epoxy/polyester powder coating
Max Load Capacity: 15 kg (33 lbs)
Mounting Hardware Included: Yes
Recommended Wall Type: Solid masonry or wooden stud

Care & Maintenance

To clean, use a soft, damp cloth. Wipe dry immediately. Do not use abrasive cleaners, scouring pads, or harsh chemicals.

CAUTION! Do not place near direct heat sources or in areas of high humidity. The shelf surface is not waterproof; wipe spills immediately.

Troubleshooting

Problem	Possible Cause	Solution
Shelf is not level	Wall markings were uneven; brackets not aligned.	Remove shelf, re-mark wall using a level, and remount.
Shelf feels loose or wobbles	Screws are not tight enough; wall plugs not suitable for wall type.	Tighten all screws. If problem persists, remove and install larger or more appropriate wall anchors.
Brackets do not align with shelf holes	Brackets may be reversed.	Check bracket orientation. The longer leg of the "L" should face the wall.
Cannot drill into wall	Drill bit is dull or incorrect for wall material.	Use a sharp, correct drill bit (masonry bit for concrete/brick).
Surface stain on shelf	Spill not cleaned promptly.	Gently clean with mild soapy water and a soft cloth. Do not scrub.

Warranty & Support

This IKEA product is covered by a limited warranty. Refer to the IKEA warranty leaflet included in the packaging or available at www.ikea.com for full terms and conditions.

Need help? Contact IKEA customer support:
Website: www.ikea.com
Phone: 1-888-888-4532
Please have the model number (194.368.32) and date of purchase ready.