IKEA EKBY ALEX 201.928.28 Shelf instructions manual

The IKEA EKBY ALEX 201.928.28 is a wall-mounted shelf system designed for storage and display. It features a clean, modern design, sturdy construction, and includes all necessary mounting hardware. Below are key sections for safety, parts list, assembly, installation, care, and warranty information.

1. Parts & Hardware Included 2. Tools Required 3. Safety Instructions 4. Assembly Steps 5. Wall Mounting Installation 6. Weight Capacity & Specifications 7. Care & Maintenance 8. Troubleshooting 9. Warranty & Support

Parts & Hardware Included

Before assembly, verify all parts are present.

Part Name	Quantity	Description
Shelf Board	1	Main shelf panel (201.928.28)
Wall Brackets	2	Metal brackets for mounting
Screws for Brackets	4	For attaching brackets to wall
Wall Plugs	4	For solid wall mounting
Assembly Instructions	1	This manual

Tools Required

You will need the following tools (not included):

Phillips screwdriver or cordless drill
Pencil
Level
Tape measure
Stud finder (recommended for locating wall studs)
Hammer (for inserting wall plugs)

Safety Instructions

WARNING! Failure to follow these instructions can result in serious injury or damage.

Check Wall Type: Ensure your wall is suitable for the load. Mount only into solid walls (concrete, brick, solid wood) or wall studs.
Use Correct Hardware: Use only the provided screws and wall plugs. For other wall types, consult a professional.
Secure Mounting: The shelf must be securely attached to the wall. Do not mount above beds, sofas, or places where people sit or sleep.
Weight Limit: Do not exceed the maximum load capacity (see Specifications).
Two-Person Job: Assembly and mounting are easier and safer with two people.

Assembly Steps

The shelf comes partially assembled. Follow these steps:

Inspect Parts: Lay out all parts and hardware on a clean, soft surface to avoid scratches.
Attach Brackets to Shelf (if required): Some models have pre-attached brackets. If not, align the brackets with the pre-drilled holes on the underside of the shelf. Secure them using the provided screws (if applicable).
Do Not Fully Tighten Yet: Leave brackets slightly loose to allow for adjustment during wall leveling.

Tip: Keep the packaging until assembly is complete in case you need to identify a part.

Wall Mounting Installation

This is the most critical step. Ensure the shelf is level and securely fixed.

Plan Position: Decide on the shelf's height and location. Use a stud finder to locate wall studs for the most secure mounting. Mark the desired height lightly with a pencil.
Mark Bracket Holes: Hold the shelf (with brackets attached) against the wall at the desired height. Use a level to ensure it is perfectly horizontal. Mark the wall through the screw holes in each bracket.
Drill Pilot Holes: At the marked points, drill pilot holes slightly smaller than the provided wall plugs. Drill depth should match the length of the wall plugs.
Insert Wall Plugs: Gently tap the wall plugs into the drilled holes until they are flush with the wall.
Mount the Shelf: Align the bracket holes with the wall plugs. Insert the screws through the brackets and into the wall plugs. Tighten securely with a screwdriver or drill.
Final Tightening: Once the shelf is securely on the wall, fully tighten any screws connecting the brackets to the shelf itself.
Check Stability: Apply gentle downward pressure to test the shelf's stability. Ensure it does not wobble or tilt.

CAUTION! If you are unsure about your wall type or mounting, seek assistance from a qualified professional.

Weight Capacity & Specifications

Model: EKBY ALEX 201.928.28
Color/Material: As specified on packaging (e.g., white, stained oak effect).
Dimensions (L x D): Refer to product packaging for exact measurements.
Maximum Load Capacity: 15 kg (33 lbs) evenly distributed. Do not place excessive weight on the front edge.
Intended Use: Indoor use only. For dry rooms.
Wall Requirements: Must be mounted to a solid, vertical wall capable of supporting the shelf and its load.

Care & Maintenance

To keep your shelf looking its best:

Cleaning: Wipe with a soft, damp cloth. Use a mild detergent if needed. Dry immediately with a soft, dry cloth.
Avoid: Abrasive cleaners, scouring pads, or harsh chemicals. Avoid prolonged exposure to direct sunlight or high humidity.
Periodic Check: Every few months, check that all mounting screws are tight.

WARNING! Do not stand or sit on the shelf. It is not designed to bear human weight.

Troubleshooting

Problem	Possible Cause	Solution
Shelf is not level	Wall markings were uneven; brackets not aligned.	Loosen screws, adjust shelf with a level, re-tighten.
Shelf feels loose or wobbles	Screws not tight; wall plugs not secure; incorrect wall type.	Tighten all screws. If problem persists, remount into a stud or solid wall section.
Brackets don't align with shelf holes	Parts may be misidentified or for a different model.	Check part numbers against the manual. Contact IKEA support if parts are incorrect.
Wall material crumbles when drilling	Old plaster or unsuitable wall.	Stop drilling. Use appropriate anchors for your wall type (not included) or consult a professional.
Scratches on shelf surface	Assembled on a hard surface.	Use a felt pad or soft cloth under the shelf during future assembly. Minor scratches can sometimes be touched up with a matching marker.

Warranty & Support

This IKEA product is covered by a limited warranty. For details, refer to the IKEA warranty booklet included with your purchase or visit www.IKEA.com.

Need Help? Visit the IKEA website for assembly guides and FAQs, or contact your local IKEA store:

Website: www.IKEA.com
Customer Support: Check your local IKEA store contact information.
Spare Parts: Available through IKEA customer service.

Important: Retain your receipt as proof of purchase for warranty claims.