IKEA DOCKSTA 193.249.95 Underframe instructions manual

The IKEA DOCKSTA 193.249.95 Underframe is a sturdy metal base designed to support the DOCKSTA table top, creating a stable dining or work surface. It features a classic round pedestal design with three legs for optimal balance, a powder-coated finish for durability, and pre-attached adjustable leveling glides to compensate for uneven floors. Below are key sections for safety, parts list, assembly, installation, care, and warranty information.

1. Parts & Hardware Included 2. Safety Instructions 3. Assembly Instructions 4. Installation & Leveling 5. Weight Capacity & Specifications 6. Care & Maintenance 7. Troubleshooting 8. Warranty & Support

Parts & Hardware Included

Before assembly, verify all parts are present. Key components: Underframe (pedestal with three legs), Pack of mounting screws, Plastic caps (if applicable).

Part Number	Description	Quantity
193.249.95	DOCKSTA Underframe (main unit)	1
114398	Wood screw (for attaching table top)	4
-	Adjustable glides (pre-attached to legs)	3
-	Instruction manual (this document)	1

Safety Instructions

Read all instructions before assembly. Ensure a clean, spacious work area.

Lifting: The underframe is heavy; use two people to move and position it.
Stability: Always install the underframe on a flat, level surface. Use the adjustable glides to stabilize.
Assembly: Use only the provided IKEA hardware. Do not overtighten screws.
Final Check: After attaching the table top, ensure all connections are secure and the table does not wobble.

WARNING! Do not stand or sit on the underframe or assembled table. The underframe is designed to support the table top and its intended load only.

Assembly Instructions

The underframe comes pre-assembled. These steps are for attaching it to the DOCKSTA table top.

Prepare: Place the table top upside down on a soft, protected surface (e.g., carpet or blanket).
Position Underframe: With help, place the underframe centered on the bottom of the table top. Align the screw holes in the underframe's top plate with the pre-drilled holes in the table top.
Attach: Insert the provided wood screws through the holes in the underframe and into the table top. Tighten firmly by hand using a screwdriver or Allen key (if provided), but do not overtighten.
Flip Table: Carefully turn the assembled table right-side up. Use two people.

Tip: Do not drag the table across the floor after assembly. Lift it to move.

Installation & Leveling

Location: Place the table on a firm, level floor.
Leveling Glides: Each leg has a threaded glide. To adjust, turn the glide clockwise to lower that corner or counter-clockwise to raise it until the table is stable and does not rock.
Final Check: Apply gentle pressure to different sides of the table to test for stability. Re-adjust glides if necessary.

CAUTION! An unlevel table is a tipping hazard. Always use the glides to achieve full stability.

Weight Capacity & Specifications

Product Name: DOCKSTA Underframe
Article Number: 193.249.95
Material: Steel, Powder coating
Color: White
Diameter (Top Plate): Approx. 30 cm
Height: Approx. 70 cm
Max Load: 50 kg (evenly distributed on the attached table top)
Compatible Table Top: IKEA DOCKSTA table top (sold separately)

Care & Maintenance

Clean with a damp cloth and mild detergent if necessary. Dry immediately.

Regular Cleaning: Wipe with a dry, soft cloth to remove dust.
Stains: For marks, use a cloth dampened with water and a mild soap. Avoid abrasive cleaners or scouring pads.
Glides: Check periodically for dirt buildup. Clean threads with a dry brush if adjustment becomes difficult.

WARNING! Do not use harsh chemicals, acids, or abrasive cleaning agents as they can damage the powder coating.

Troubleshooting

Issue	Possible Cause	Solution
Table wobbles	Floor uneven or glides not adjusted	Use the adjustable glides on each leg to level the table. Turn until stable.
Screws are loose	Not fully tightened during assembly	Tighten the screws connecting the underframe to the table top. Do not overtighten.
Underframe seems unstable	Legs may not be fully seated (if applicable)	Ensure the underframe was not damaged during transport. All welds should be intact.
Difficulty adjusting glides	Dirt in threads or cross-threaded	Clean the glide threads. Turn counter-clockwise to disengage, then re-engage carefully.
Table top does not align with screw holes	Wrong table top or misaligned underframe	Verify you have the DOCKSTA table top. Center the underframe perfectly before screwing.

Warranty & Support

This IKEA product is covered by a limited warranty. Refer to the IKEA warranty terms included with your purchase or available at IKEA stores.

Need Help? For assembly support, missing parts, or more information:

Visit the IKEA website: www.ikea.com
Contact your local IKEA store.
Refer to the product page for the DOCKSTA series for specific guides.

Recycling: At end of life, disassemble and recycle materials according to local regulations. Steel is widely recyclable.