IKEA BROR 094.717.41 Post instructions manual

The IKEA BROR 094.717.41 Post is a versatile, heavy-duty steel post designed for use with the BROR modular storage system. It is intended for creating sturdy shelving, workbenches, and storage units in garages, workshops, or utility rooms. The post features pre-drilled holes for easy assembly and adjustment, a durable powder-coated finish, and compatibility with various BROR shelves and accessories. Below are key sections for safety, features, installation, setup, use, maintenance, and troubleshooting.

1. Features at a Glance 2. Package Contents 3. Safety Information 4. Tools Required 5. Assembly Instructions 6. Mounting & Installation 7. Adjusting Shelves 8. Weight Capacity 9. Care & Maintenance 10. Troubleshooting 11. Warranty & Support

Features at a Glance

Key components: Heavy-gauge steel post, pre-drilled adjustment holes, corrosion-resistant powder coating, compatible with BROR system brackets and shelves.

Feature	Description
Material	Heavy-duty steel with powder-coated finish
Dimensions	Standard post height and width as per model specifications
Pre-drilled holes	For easy attachment of brackets at multiple heights
Compatibility	Designed for use with BROR shelving, workbench tops, and accessories
Finish	Durable, scratch-resistant coating in dark gray/black
Load capacity	High weight rating when properly installed (see specifications)

Package Contents

Unpack and verify all parts are included before starting assembly.

BROR Post (094.717.41) - Quantity as specified in your purchase.
Mounting hardware (screws, bolts, washers) - included in accessory packs or shelving kits.
Instruction manual (this document).

NOTE: Shelves, brackets, and worktops are sold separately. Ensure you have all necessary BROR system components.

Safety Information

Read all instructions before assembly and use.

Use on stable, level surfaces only.
Ensure the structure is securely anchored to wall or floor if required for stability.
Do not exceed the maximum load capacity specified for the post and shelving system.
Wear safety glasses during assembly to protect eyes from debris.
Keep away from children during assembly to prevent injury from small parts or sharp edges.

WARNING! Heavy components; lift with care and use assistance. Ensure all connections are tight and secure before loading.

Tools Required

Gather these tools before beginning assembly:

Phillips screwdriver or cordless drill with Phillips bit
Adjustable wrench or socket set
Level
Tape measure
Pencil for marking
Safety glasses

Tip: Using a cordless drill can significantly speed up the assembly process.

Assembly Instructions

Follow these steps to assemble a basic BROR shelving unit using the posts.

Prepare the area: Clear space and lay out all components.
Attach brackets to posts: Align bracket holes with desired height holes on post. Insert and tighten bolts using wrench.
Connect posts to form frame: For multi-bay units, connect posts with horizontal braces using provided hardware.
Install shelves: Place shelf onto brackets. For secured shelves, use screws through bracket into shelf bottom.
Check stability: Ensure unit is level and all bolts are tightened securely.

CAUTION! Do not skip any steps. An improperly assembled unit may collapse.

Mounting & Installation

For added stability, especially for tall or heavily loaded units, secure to wall or floor.

Position the assembled unit in its desired location.
Use a level to ensure it is plumb and square.
Mark drilling points on wall/floor through mounting holes in posts or brackets.
Drill pilot holes appropriate for your wall/floor material (concrete, wood, drywall).
Insert wall anchors if needed, then secure the unit using appropriate screws/bolts.

Tip: For concrete floors or walls, use a hammer drill and concrete anchors.

Adjusting Shelves

One of the key features is the adjustable shelf height.

Unload the shelf completely.
Support the shelf while loosening the bolts on the supporting brackets.
Slide brackets up or down to align with the desired set of holes on the post.
Re-tighten bolts securely.
Replace shelf and reload items.

WARNING! Never adjust shelves while they are loaded. Always empty them first.

Weight Capacity

Maximum load per post: Refer to the specific BROR system technical sheet. Capacity depends on configuration and anchoring.
Distribute weight evenly: Do not concentrate excessive weight in one area.
Dynamic load vs. static load: Shelves holding tools or equipment that are frequently accessed have a lower effective capacity than static storage.
Factor of safety: For safety, do not load shelves beyond 75% of the stated maximum capacity.

Care & Maintenance

To ensure longevity of your BROR post and system.

Cleaning: Wipe with a damp cloth and mild detergent. Dry immediately.
Avoid abrasives: Do not use scouring pads or harsh chemicals that can damage the powder coat.
Regular inspection: Periodically check all bolts and connections for tightness, especially if the unit is subject to vibration.
Rust prevention: If the finish is scratched, touch up with matching paint to prevent rust.

CAUTION! Do not use pressure washers or steam cleaners.

Troubleshooting

Symptom	Possible Cause	Corrective Action
Unit wobbles or is unstable	Uneven floor; loose bolts; not anchored to wall	Use shims to level; tighten all connections; secure to wall stud or solid surface.
Shelf sags under weight	Exceeded weight limit; shelf not properly supported	Reduce load; ensure shelf is centered on brackets; use thicker shelf or additional support.
Difficulty aligning holes	Frame out of square; posts misaligned	Loosen all bolts slightly, square the frame, then re-tighten from the base upward.
Rust spots appearing	Finish damaged; high humidity environment	Sand area lightly, clean, and apply touch-up paint. Keep in a drier location if possible.
Bolts won't tighten	Stripped threads; wrong bolt size	Replace damaged bolt; ensure you are using the correct hardware from the BROR system.

Warranty & Support

IKEA BROR products are covered by IKEA's commercial warranty. Refer to the IKEA warranty terms for specific duration and conditions.

For assembly help: Visit the IKEA website and search for the product assembly video or PDF guide.

For missing parts: Contact your local IKEA store or use the spare parts service online.

Customer Support: Visit www.ikea.com or contact your local IKEA store.