IKEA BROGRUND 194.409.14 Faucet instructions manual

The IKEA BROGRUND 194.409.14 is a single-lever kitchen faucet designed for easy installation and reliable operation. It features a pull-out spray head, ceramic disc cartridge for smooth temperature and flow control, a durable metal construction with chrome finish, and a flexible hose. Below are key sections for safety, features, installation, operation, maintenance, and troubleshooting.

1. Features at a Glance 2. Installation 3. First-Time Setup 4. Specifications 5. Controls and Operation 6. Connecting to Water Supply 7. Using the Pull-Out Spray Head 8. Maintenance & Cleaning 10. Regulatory Information 11. Troubleshooting

Features at a Glance

Key components: Single-lever handle, Pull-out spray head with hose, Ceramic disc cartridge, Aerator, Mounting hardware.

Feature	Description
Single-lever handle	Controls both water temperature and flow rate
Pull-out spray head	Extends for flexible rinsing; retracts automatically
Ceramic disc cartridge	Ensures smooth operation and drip-free performance
Aerator	Mixes air with water for efficient flow and reduced splashing
Flexible hose	Provides reach and mobility for the spray head
Chrome finish	Durable and easy-to-clean surface
Mounting hardware	Includes nuts, washers, and gaskets for secure installation

Installation

Unpack and inspect all parts. Ensure you have the necessary tools (adjustable wrench, plumber's tape).

Prepare the sink: Clean the mounting area and ensure the sink hole is the correct size (standard 1-3/8" or 35mm).
Install the faucet: Insert the faucet body through the sink hole from above. Secure from below with the mounting nut and washer.
Connect the supply lines: Attach the hot and cold water supply lines (flexible hoses provided) to the corresponding valves under the sink. Use plumber's tape on threads.
Connect the spray hose: Attach the pull-out spray hose to the faucet outlet and secure.
Check for leaks: Turn on water supply slowly and inspect all connections.

WARNING! Ensure water supply is turned OFF before installation. Do not overtighten connections.

First-Time Setup

After installation, perform initial checks and adjustments.

Flush the faucet: Run both hot and cold water for a few minutes to clear any debris from the lines.
Test the spray head: Pull out the spray head and check retraction. Adjust hose weight if necessary.
Check handle operation: Move lever smoothly from off to full flow, and from cold to hot.
Inspect for leaks: Look for drips at connections, handle base, and spray head.

CAUTION! Test with low water pressure first to avoid sudden spray.

Specifications

Model: BROGRUND 194.409.14
Type: Single-lever kitchen faucet with pull-out spray
Finish: Chrome
Cartridge: Ceramic disc
Hose Length: Approximately 1.5 meters (59 inches)
Spray Patterns: Stream and spray
Maximum Pressure: 0.5 MPa (5 bar, 72.5 psi)
Installation: Single-hole sink mounting
Warranty: Refer to IKEA warranty terms

Controls and Operation

Handle Controls: Lift lever to turn on water; move left for hot, right for cold. Push down to turn off.

Spray Head: Pull out to extend; release to retract. Button on spray head switches between stream and spray patterns.

Aerator: Can be removed for cleaning if water flow decreases.

Connecting to Water Supply

Use only standard 1/2" water supply lines. Ensure hot (left) and cold (right) are correctly connected.

Turn off main water supply and open faucet to drain lines.
Wrap threads with plumber's tape clockwise.
Hand-tighten connections, then use wrench for a quarter turn more.
Slowly turn water back on and check for leaks.

Tip: Label hot and cold lines if not color-coded.

Using the Pull-Out Spray Head

Designed for flexible cleaning and rinsing.

To extend: Simply pull the spray head from its dock.
To switch patterns: Press the button on the spray head while water is flowing.
To retract: Gently guide the hose back; the weight will help retract it fully.
To dock: Ensure spray head clicks securely into place.

WARNING! Do not pull the hose forcefully or at sharp angles. Do not let the spray head hang freely.

Maintenance & Cleaning

Regular cleaning ensures longevity and performance.

Clean with mild soap and water; dry with a soft cloth.
Do not use abrasive cleaners, scouring pads, or acidic substances.
Clean aerator periodically: Unscrew from spout tip, rinse under water, and reinstall.
Check hose for kinks or damage.

CAUTION! Do not use harsh chemicals; they can damage the finish.

Regulatory Information

This product complies with applicable plumbing standards and regulations. Manufactured for IKEA. For warranty and support, contact IKEA customer service or visit www.ikea.com.

Troubleshooting

Symptom	Possible Cause	Corrective Action
Low water pressure	Clogged aerator	Remove and clean aerator.
Spray head not retracting	Kinked hose or faulty weight	Straighten hose; check weight movement.
Leak at base	Loose mounting nut or worn cartridge	Tighten mounting nut; replace cartridge if needed.
Handle is stiff	Debris in cartridge	Flush system; replace cartridge.
Water temperature inconsistent	Supply line issues or cartridge problem	Check hot/cold supply; replace cartridge.

Service: For persistent issues, contact IKEA customer support or a qualified plumber.