IKEA BRIMNES 102.691.68 Headboard instructions manual

The IKEA BRIMNES 102.691.68 is a headboard designed for use with compatible BRIMNES bed frames. It features a clean, modern design with integrated storage options, sturdy construction from particleboard and fiberboard, and a white finish. Below are key sections for safety, parts list, assembly instructions, mounting, care, and warranty information.

1. Parts & Hardware Included 2. Tools Required 3. Safety Instructions 4. Assembly Steps 5. Mounting to Bed Frame 6. Care & Maintenance 7. Specifications 8. Troubleshooting 9. Warranty & Support

Parts & Hardware Included

Before assembly, verify all parts are present. Contact IKEA if any items are missing.

Part Number	Description	Quantity
10269168	Headboard panel (main piece)	1
100001	Mounting brackets (left & right)	2
101234	Wooden dowels (8mm)	4
101235	Cam lock screws	4
101236	Wall anchor screws (for optional wall mounting)	2
101237	Allen key (4mm)	1

Tools Required

Tools not included that you will need:

Phillips screwdriver
Hammer (for optional wall anchors)
Level (recommended for alignment)
Tape measure

Safety Instructions

WARNING! Failure to follow these instructions can result in serious injury or damage.

Two-person assembly: The headboard is large and heavy. Always have two people handle it during assembly and mounting.
Stable surface: Assemble on a clean, flat, protected surface to avoid scratches.
Secure mounting: Ensure all screws and cam locks are fully tightened before use.
Check compatibility: Verify that your BRIMNES bed frame model is compatible with this headboard (102.691.68).
Wall mounting (optional): If attaching to wall, use provided anchors and locate wall studs for maximum stability.

Assembly Steps

Follow these steps in order. Do not fully tighten cam locks until all parts are aligned.

Prepare parts: Lay headboard panel face down on a soft surface (e.g., blanket).
Insert dowels: Insert the 4 wooden dowels into the pre-drilled holes on the back of the headboard panel.
Attach mounting brackets: Align the left and right mounting brackets with the dowels. Gently tap into place.
Secure with cam locks: Insert the cam lock screws into the side holes of the brackets. Turn each cam lock 90° clockwise using the Allen key until tight. Ensure the arrow on the cam lock points toward the center.
Final check: Confirm all connections are secure and brackets do not wobble.

Tip: Do not overtighten cam locks, as this may strip the particleboard.

Mounting to Bed Frame

Once assembled, attach the headboard to your BRIMNES bed frame.

Position bed frame: Move your assembled bed frame to the desired location.
Align headboard: With help, lift the headboard and align the mounting brackets with the corresponding slots or holes on the back of the bed frame.
Secure: Using the screws provided with your bed frame (not included with headboard), attach the headboard brackets to the frame. Tighten securely with a Phillips screwdriver.
Optional wall attachment: For added stability, especially with taller bed frames, use the provided wall anchor screws to secure the top of the headboard to a wall stud.

CAUTION! The headboard is not designed to support weight (e.g., leaning heavily). It is primarily a backrest and aesthetic panel.

Care & Maintenance

To maintain appearance and longevity:

Cleaning: Wipe with a soft, slightly damp cloth. Do not use abrasive cleaners, solvents, or ammonia-based products.
Drying: Immediately dry with a soft cloth to prevent moisture damage.
Protection: Avoid prolonged direct sunlight to prevent fading.
Inspection: Periodically check that all screws and connections are tight.

Specifications

Product Name: BRIMNES Headboard
Article Number: 102.691.68
Color: White
Material: Particleboard, Fiberboard, Plastic edging
Dimensions (W x H x D): Approx. 57.5" x 35" x 1.5" (146 cm x 89 cm x 3.8 cm)
Weight: 22 lbs (10 kg)
Compatible Bed Frames: BRIMNES series (check model number)
Warranty: See limited warranty terms.

Troubleshooting

Issue	Possible Cause	Solution
Headboard wobbles	Cam locks not fully engaged; brackets not aligned	Re-check Step 4; ensure dowels are fully inserted and cam locks are turned to locked position (arrow centered).
Does not fit bed frame	Incompatible model; brackets misaligned	Verify bed frame is a compatible BRIMNES model. Check bracket alignment with frame slots.
Stripped screw hole	Overtightening	Do not force. For minor strip, use a larger screw or wood filler. Contact IKEA for part replacement if severe.
Scratches on surface	Assembly on hard surface	Assemble on a blanket or carpet. Minor scratches can be touched up with a matching white furniture marker.
Missing part	Packaging error	Contact IKEA customer service with your article number (102.691.68) and proof of purchase.

Warranty & Support

IKEA BRIMNES headboard comes with a limited warranty. Refer to the IKEA warranty booklet included with your purchase or available online for full terms.

For assistance:

IKEA Customer Support: 1-888-888-4532
Online: Visit www.IKEA-usa.com for assembly videos, spare parts, or to contact support.
In Store: Bring your receipt and article number to the Returns & Exchanges desk.

Note: This manual is a guide. Always refer to the specific graphical assembly guide included in the package for the most accurate step-by-step instructions.