IKEA BOAXEL 304.637.44 Shelf instructions manual

The IKEA BOAXEL 304.637.44 is a versatile wall-mounted shelving system designed for flexible storage in various rooms. It consists of wall uprights, shelf brackets, shelves, and mounting hardware, allowing for customizable configurations. Below are key sections for safety, parts list, tools needed, assembly instructions, mounting guidelines, configuration options, care, and troubleshooting.

Parts List & Included Components

Verify all parts are present before starting assembly.

Tools Required

Tools not included that you will need:

• Power Drill (recommended) or Screwdriver
• Hammer (for tapping in wall anchors)
• Stud Finder (for locating wall studs)
• Tape Measure
• Pencil
• Level (at least 24 inches)

Safety Instructions

WARNING! Failure to follow these instructions can result in serious injury or damage.

1. Wall Strength: Mount only to solid walls (wood studs, concrete, brick). Do not mount solely to drywall/plaster without proper anchors.
2. Weight Limit: Do not exceed maximum load per shelf (see Specifications). Distribute weight evenly.
3. Child Safety: Do not allow children to climb on shelves. Secure heavy items on higher shelves.
4. Two-Person Job: Assembly and mounting may require two people to safely handle parts.
5. Tool Safety: Use tools properly; wear safety glasses if drilling.

Assembly Steps

Assemble components before mounting to wall.

1. Lay Out Parts: Unpack and identify all parts using the Parts List.
2. Attach Brackets to Uprights: Hook shelf brackets into desired slots on uprights. Use included Allen key to tighten locking screws on brackets.
3. Place Shelves: Rest shelf boards on top of installed brackets. Ensure they are centered and secure.
4. Check Stability: Gently test assembly on floor before wall mounting.

Tip: Assemble on a soft surface (carpet, blanket) to avoid scratching parts.

Wall Mounting Guide

Proper mounting is critical for safety.

1. Locate Studs: Use stud finder to locate wooden wall studs. Mark center of each stud with pencil.
2. Plan Layout: Decide height and spacing of uprights. Use level and tape measure to mark drilling points. Uprights must be level and parallel.
3. Drill Pilot Holes: At marked points, drill pilot holes slightly smaller than wall anchors/screws. For studs, drill directly into wood.
4. Insert Anchors: For drywall without stud, tap plastic wall anchors into holes until flush with wall.
5. Mount Uprights: Align upright with holes. Insert and tighten screws using drill/screwdriver. Do not overtighten.
6. Final Check: Ensure uprights are firmly attached and level. Apply gentle downward pressure to test.

CAUTION! If you hit electrical wiring or plumbing, stop immediately and choose a new location.

Shelf Configuration Options

The BOAXEL system is highly customizable.

• Adjustable Height: Brackets can be placed in any slot on uprights, allowing shelves to be spaced as needed.
• Multiple Widths: Shelves can be placed at different depths by using different bracket positions.
• Combination Use: Can be combined with other BOAXEL components (baskets, hooks) for added functionality.
• Room Versatility: Suitable for living room, bedroom, office, garage, or entryway storage.

Weight Limits & Specifications

• Max Load per Shelf: 15 kg (33 lbs) evenly distributed.
• Total System Load: Do not exceed 45 kg (99 lbs) across all shelves.
• Material: Steel uprights and brackets; Particleboard/wood shelves.
• Finish: White powder-coated steel; White stained oak veneer (or as per product variant).
• Dimensions (approx.): Upright height: 100 cm; Shelf depth: 30 cm; Width configurable.

Note: Weight limits assume proper mounting into wall studs or with appropriate anchors.

Care & Maintenance

To ensure longevity of your shelving unit.

1. Cleaning: Wipe shelves with a dry or slightly damp cloth. Do not use abrasive cleaners or chemicals.
2. Avoid Moisture: Do not install in constantly damp areas (e.g., bathroom without ventilation).
3. Regular Check: Periodically tighten screws and brackets. Check wall mounting points for stability.

CAUTION! Do not use wax, polish, or silicone-based sprays on shelves.

Disassembly & Relocation

To move or reconfigure your shelves.

1. Remove all items from shelves.
2. Unscrew shelf boards from brackets (if attached).
3. Loosen bracket locking screws and remove brackets from uprights.
4. Unscrew uprights from wall carefully. Patch old screw holes if desired.
5. Follow Wall Mounting Guide to reinstall in new location.

Warranty Information

IKEA Limited Warranty: This product is covered by IKEA's standard limited warranty. Refer to the IKEA warranty document included with your purchase or available at www.ikea.com. Warranty covers material and manufacturing defects under normal household use. Damage due to improper assembly, mounting, overload, or accidents is not covered. For service, contact your local IKEA store or visit the IKEA website.

Troubleshooting

Need Help? Visit www.ikea.com or contact your local IKEA store for assembly support or spare parts.